06-23-2005
determining open ports
hi all
1) how to determine available ports in a box (solaris)
do i have to go for a netstat on all the ports?
2) how to block a particular port for a particular type of connection.
Any help would be greatly appreciated
Thanks
9 More Discussions You Might Find Interesting
1. Cybersecurity
/* Linux Slackware */
Nmap shows the following ports open on the gateway.
21/tcp ftp
22/tcp ssh
23/tcp telnet
25/tcp smtp
37/tcp time
80/tcp http
113/tcp auth
515/tcp printer
587/tcp submission
1024/tcp kdm
6000/tcp x11
-------------------------------
i would like to close as... (10 Replies)
Discussion started by: LowOrderBit
10 Replies
2. Linux
how can i open ports i need in red hat server vs root access ? (7 Replies)
Discussion started by: Sirius
7 Replies
3. Shell Programming and Scripting
Hello, i need a script (bash type maybe?..), which would check open ports on 127.0.0.1 and then compare open ports with "registered/allowed" port list and try to kill the program who uses unregistered ports. It would be great that script would be started lets say every 5 or 10 minutes.
You see i... (2 Replies)
Discussion started by: MorchiuS
2 Replies
4. AIX
Hi Every body,
What is the command on AIX 5.2 that can be used to get all open ports? (2 Replies)
Discussion started by: aldowsary
2 Replies
5. Solaris
Hello,
I have a number of Solaris 8 Sun servers that have open ports that I cannot identify. I see some with 1013-1023 (which are reserved ports according to the IANA. Lsof does not identify these. I rebooted the server and they went off, but this morning I saw they were all back on again. Any... (1 Reply)
Discussion started by: csgonan
1 Replies
6. IP Networking
I'm fairly new to networking and am trying to figure our network out, as I was recently assigned to be network administrator where I work. I was trying to get utorrent to work but am not having success in figuring out what's blocking my ports. As of now, I'm getting connected from a mikrotik... (11 Replies)
Discussion started by: brandonros
11 Replies
7. Solaris
hi guys,
may i know the exact steps to open a port in solaris.i have some rough idea - which is adding the port number in /etc/services.
but i am not sure the correct conventions, steps or any other steps.
kindly advise.thanks guys ! (1 Reply)
Discussion started by: cromohawk
1 Replies
8. UNIX for Dummies Questions & Answers
just a quick question:
a. whats the simplest command to check open port and the corresponding services?
example:
bash-2.05# netstat -an | grep LISTEN
*.199 *.* 0 0 49152 0 LISTEN
*.8989 *.* 0 0 49152 ... (1 Reply)
Discussion started by: lhareigh890
1 Replies
9. IP Networking
Hi,
I have read some forum theads about the open and close ports. some points are clear and it is not working on my machine or something am i missing?
I have commented out a port /etc/services, one application uses
then when i use the telnet <hostname> <port_blocked> it shows connected..... (1 Reply)
Discussion started by: balamv
1 Replies
dc(4) Kernel Interfaces Manual dc(4)
Name
dc - serial line/mouse/keyboard
Syntax
device dc0 at ibus? vector dcintr
Description
The serial line controller provides four ports, with modem control on two of the ports. The DECstation 3100 and DECstation 2100 only pro-
vide partial modem control. The DECstation 5000 provides full modem control. The ports are used as follows:
Port Usage
0 Graphics device keyboard at 4800 BPS
1 Mouse or tablet at 4800 BPS
2 Communications port 1 (w/modem control)/local terminal
3 Communications port 2 (w/modem control)/local terminal
Each communication port from the serial line controller behaves as described in and can be set to run at any of 16 speeds. For the encod-
ing, see
When a graphics device is not being used as the system console, communications port 2 becomes the system console. In this configuration,
the port can only be used at 9600 BPS and no modem control is supported.
The serial line driver operates in interrupt-per-character mode (all pending characters are flushed from the silo on each interrupt).
Restrictions
Speed must be set to 9600 BPS on the console port and 4800 BPS on ports used by graphics devices. The serial line driver enforces this
restriction; that is, changing speeds with the command may not always work on these ports.
Files
console terminal
local terminal
local terminal
See Also
console(4), devio(4), tty(4), ttys(5), MAKEDEV(8)
RISC dc(4)