RAID 1 on SWAP file? Post: 75805

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Swap file

I just started working with AIX and need a little help. Is there a command to find the size of the swap file.

2. Solaris

Swap config - Mirror swap or not?

Hello and thanks in advance. I have a Sun box with raid 1 on the O/S disks using solaris svm. I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space. I have been warned not to do this by some...

3. HP-UX

Swap device file and swap sapce

Hi I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system: - I would like to know when does the memory swap space spill over to the device swap space? - And how much % of memory swap utilization should be specified (swap space device...

4. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help.

5. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI...

6. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My...

7. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i...

8. AIX

RAID 10 Failed Drive Swap

I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can...

9. Solaris

Explain the output of swap -s and swap -l

Hi Solaris Folks :), I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands. $swap -s total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available $swap -l swapfile dev swaplo...

LEARN ABOUT V7

ataraid

ATARAID(4)						   BSD Kernel Interfaces Manual 						ATARAID(4)

NAME

     ataraid -- ATA software RAID support

SYNOPSIS

     device ata
     device ataraid

DESCRIPTION

     The ataraid driver provides support for so-called software RAID (sometimes referred to as fake RAID or pseudo RAID).

     When a controller that supports software RAID is instructed to create a RAID array, its BIOS writes data structures in a specific metadata
     format to the disks.  These data structures are picked up by the ataraid driver, so that FreeBSD can work with the array.	The ataraid driver
     has to understand the specific metadata format of a controller BIOS in order to support its RAID capabilities.

     Read-only support for a metadata format means that FreeBSD can use the given RAID array for normal read/write operations.	Creation and
     rebuild of such arrays has to be done from the controller BIOS.

     Read and write support for a metadata format means that FreeBSD can use the given RAID array for normal read/write operations.  Additionally,
     the atacontrol(8) utility can be used to create, rebuild, update and fail such RAID arrays.

     The ataraid driver can read the following metadata formats:

     o	 Adaptec HostRAID
     o	 Highpoint V2 RocketRAID
     o	 Highpoint V3 RocketRAID
     o	 Intel MatrixRAID
     o	 Integrated Technology Express (ITE)
     o	 JMicron
     o	 LSI Logic V2 MegaRAID
     o	 LSI Logic V3 MegaRAID
     o	 NVIDIA MediaShield
     o	 Promise FastTrak
     o	 Silicon Image Medley
     o	 Silicon Integrated Systems (SiS)
     o	 VIA Tech V-RAID
     o	 FreeBSD PseudoRAID

     The ataraid driver can write the following metadata formats:

     o	 Highpoint V2 RocketRAID
     o	 Intel MatrixRAID
     o	 JMicron
     o	 Promise FastTrak
     o	 Silicon Integrated Systems (SiS)
     o	 VIA Tech V-RAID
     o	 FreeBSD PseudoRAID

     It is also possible to use software RAID on controllers that do not have special software RAID capabilities.  See atacontrol(8) for details.

FILES

     /dev/ar*  ATA RAID device nodes

SEE ALSO

     ata(4), atacontrol(8)

CAVEATS

     RAID5 is not supported at this time.  Code exists, but it neither uses nor maintains parity information.

AUTHORS

     The ataraid driver was written by Soren Schmidt <sos@FreeBSD.org>.  This manual page was written by Christian Brueffer
     <brueffer@FreeBSD.org>.

BSD
								 February 17, 2006							       BSD