06-08-2005
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi:-
I am trying to install a device driver for Intel NIC card on TurboLinux, but getting following errors,
cc -O -Wall -o eepro100-diag eepro100-diag.c
eepro100-diag.c:72: unistd.h: No such file or directory
eepro100-diag.c:73: stdio.h: No such file or directory
eepro100-diag.c:74:... (1 Reply)
Discussion started by: s_aamir
1 Replies
2. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. Solaris
I have a Sun Blade 2500 with SUN 5.9 OS installed. I have one NIC built-in which is working fine.
I insert another new NIC in the machine with four RJ45 connector options(means four NICs in one Card). The problem is i am not able to see the new NIC
Thanks (13 Replies)
Discussion started by: z_haseeb
13 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. Virtualization and Cloud Computing
hi guys
I am using Suse 11 in virtual enviroment using vmware.
For some reasons I need to add a new virtual nic or just a nic to my suse 11.
so is there a way to add this new NIC to my Suse 11 without restarting?
thanks a lot
---------- Post updated 01-24-13 at 01:22 AM ----------... (0 Replies)
Discussion started by: karlochacon
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT SUSE
ocf_heartbeat_viparip
OCF_HEARTBEAT_VIPARI(7) OCF resource agents OCF_HEARTBEAT_VIPARI(7)
NAME
ocf_heartbeat_VIPArip - Manages a virtual IP address through RIP2
SYNOPSIS
VIPArip [start | stop | monitor | validate-all | meta-data]
DESCRIPTION
Virtual IP Address by RIP2 protocol. This script manages IP alias in different subnet with quagga/ripd. It can add an IP alias, or remove
one.
SUPPORTED PARAMETERS
ip
The IPv4 address in different subnet, for example "192.168.1.1". (required, string, no default)
nic
The nic for broadcast the route information. The ripd uses this nic to broadcast the route informaton to others (optional, string,
default eth0)
zebra_binary
Absolute path to the zebra binary. (optional, string, default /usr/sbin/zebra)
ripd_binary
Absolute path to the ripd binary. (optional, string, default /usr/sbin/ripd)
SUPPORTED ACTIONS
This resource agent supports the following actions (operations):
start
Starts the resource. Suggested minimum timeout: 20s.
stop
Stops the resource. Suggested minimum timeout: 20s.
monitor
Performs a detailed status check. Suggested minimum timeout: 20s. Suggested interval: 5s.
validate-all
Performs a validation of the resource configuration. Suggested minimum timeout: 20s.
meta-data
Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5s.
EXAMPLE
The following is an example configuration for a VIPArip resource using the crm(8) shell:
primitive example_VIPArip ocf:heartbeat:VIPArip
params
ip=string
op monitor depth="0" timeout="20s" interval="5s"
SEE ALSO
http://www.linux-ha.org/wiki/VIPArip_(resource_agent)
AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors)
resource-agents 1.0.3 07/05/2010 OCF_HEARTBEAT_VIPARI(7)