Sponsored Content
Full Discussion: nic configuration
Top Forums UNIX for Dummies Questions & Answers nic configuration Post 74270 by nadav on Wednesday 8th of June 2005 05:38:03 PM
Old 06-08-2005
thanks!

many thanks!
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

NIC Driver

Hi:- I am trying to install a device driver for Intel NIC card on TurboLinux, but getting following errors, cc -O -Wall -o eepro100-diag eepro100-diag.c eepro100-diag.c:72: unistd.h: No such file or directory eepro100-diag.c:73: stdio.h: No such file or directory eepro100-diag.c:74:... (1 Reply)
Discussion started by: s_aamir
1 Replies

2. Solaris

Cause of NIC changes ...?

Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1... But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies

3. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

4. Solaris

Not able to find the new NIC

I have a Sun Blade 2500 with SUN 5.9 OS installed. I have one NIC built-in which is working fine. I insert another new NIC in the machine with four RJ45 connector options(means four NICs in one Card). The problem is i am not able to see the new NIC Thanks (13 Replies)
Discussion started by: z_haseeb
13 Replies

5. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

6. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

7. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

8. Virtualization and Cloud Computing

Rediscover a new NIC

hi guys I am using Suse 11 in virtual enviroment using vmware. For some reasons I need to add a new virtual nic or just a nic to my suse 11. so is there a way to add this new NIC to my Suse 11 without restarting? thanks a lot ---------- Post updated 01-24-13 at 01:22 AM ----------... (0 Replies)
Discussion started by: karlochacon
0 Replies

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
OCF_HEARTBEAT_SENDAR(7) 					OCF resource agents					   OCF_HEARTBEAT_SENDAR(7)

NAME
ocf_heartbeat_SendArp - Broadcasts unsolicited ARP announcements SYNOPSIS
SendArp [start | stop | monitor | meta-data | validate-all] DESCRIPTION
This RA can be used _instead_ of the IPaddr2 or IPaddr RA to send gratuitous ARP for an IP address on a given interface, without adding the address to that interface. For example, if for some resaon you wanted to send gratuitous ARP for addresses managed by IPaddr2 or IPaddr on an additional interface. SUPPORTED PARAMETERS
ip The IP address for sending ARP packet. (required, string, no default) nic The NIC for sending ARP packet. (required, string, no default) SUPPORTED ACTIONS
This resource agent supports the following actions (operations): start Starts the resource. Suggested minimum timeout: 20s. stop Stops the resource. Suggested minimum timeout: 20s. monitor Performs a detailed status check. Suggested minimum timeout: 20. Suggested interval: 10. meta-data Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5. validate-all Performs a validation of the resource configuration. Suggested minimum timeout: 20s. EXAMPLE
The following is an example configuration for a SendArp resource using the crm(8) shell: primitive p_SendArp ocf:heartbeat:SendArp params ip=string nic=string op monitor depth="0" timeout="20" interval="10" SEE ALSO
http://www.linux-ha.org/wiki/SendArp_(resource_agent) AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors) resource-agents UNKNOWN 03/09/2014 OCF_HEARTBEAT_SENDAR(7)
All times are GMT -4. The time now is 07:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy