09-25-2001
what it actually does is it brings your system down to the PROM prompt (the ok prompt), then you have to boot from there. Because this command wipes out your original network configuration, you will be placed into an interactive configuration mode upon boot. just follow the bouncing ball when it asks the questions and you should be fine. It has worked for me every time so far.
10 More Discussions You Might Find Interesting
1. IP Networking
I have managed to setup my Solaris box to receive an IP number from a DHCP server. In addition, I can ping and telnet between my dhcp server and my solaris box using the IP number. However, I can't resolve addresses by name from my solaris box.
In my nsswitch.conf file I have:
hosts: dns
... (4 Replies)
Discussion started by: marist89
4 Replies
2. Solaris
How is it possible to derive the very next IP that the solaris dhcp server is going to assign to the next host that requests? (0 Replies)
Discussion started by: ne0phyte
0 Replies
3. Solaris
Can any one tell me how to stop DHCP service on Solaris 10 so that it should not start nextime when the system is rebooted. (2 Replies)
Discussion started by: shabu
2 Replies
4. Solaris
I am trying to set up a DHCP on Sunblade 100. I have Dlink router that connects me to the net with my other computers. I can't seem to let my DHCP server to give out IP addresses instead of my router. I have been working on this for the last three days. I had an issue with Unknown name but i have... (4 Replies)
Discussion started by: aliban83
4 Replies
5. UNIX for Dummies Questions & Answers
I have a new solaris machine and I am trying to bring the same on network. The IP assignemnt is via DHCP. I want to know as which files need to be modified to include DHCP server IP in order that the machine gets its IP via DHCP server.
Thanks in Advance. :) (1 Reply)
Discussion started by: Ashvin Gaur
1 Replies
6. Solaris
Hello,
I need to configure a Cisco VLAN Accesspoint with DHCP using Solaris
dhtadm & pntadm
Network: 10.10.122.0 255.255.255.0
Default Router 10.10.122.1
Scope Range 10.10.122.10 - 254
Option 60 “Cisco AP c1142”
Option 43 ... (0 Replies)
Discussion started by: fredy82
0 Replies
7. Solaris
Dear All,
I have following configuration solaris 10 host
interface e1000g0 hold IP 10.124.73.178 having internet access natted to public ip on cisco switch
interface e1000g1 hold IP 192.168.8.10 DHCP server with DHCP client IP ranges 192.168.8.11 to 192.168.8.15
/etc/defaultrouter hold... (4 Replies)
Discussion started by: patel1678
4 Replies
8. Solaris
I need to find out the MAC address of an IP leased from DHCP server .
For Eg:-i need to know the MAC of the below mentioned IP at the below mentioned time .
IP : 172.16.28.90
Date :Sunday July 2nd 2011
Time : 14.07.2011
OS -Solaris 10
Vital QIP IP management software using to... (0 Replies)
Discussion started by: sandeep.tk
0 Replies
9. Solaris
Hi All,
Could you please let me know how can we check whether any given solaris machien is using DHCP or not.
is ps -ef | grep dhcp is full proof method or is their any other way. (10 Replies)
Discussion started by: omkar.jadhav
10 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)