Sponsored Content
Special Forums IP Networking unable to bring up any interface Post 7204 by Andy Hibbins on Thursday 20th of September 2001 02:01:09 PM
Old 09-20-2001
Hi alam,

What type of ethernet card have you got installed?
Also what error messages are being displayed when you attempt to bring up lo and eth0?


Andy H
 

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Unable to bring up Sun OS

The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the... (2 Replies)
Discussion started by: mayewil
2 Replies

2. Solaris

Unable to bring a disk from error to online state.

Hello experts. I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format. Commands i used and output are.... #vxdisk list DEVICE TYPE ... (11 Replies)
Discussion started by: younus_syed
11 Replies

3. IP Networking

Unable to start network interface

Hi (sorry for my bad English) I'm trying to configure an US Robotics (USR5423) wirless usb adapter on Fedora 9. the device is detected, and i'm trying to configure a wireless connection. When I want to activate the device using #service network restart or # /etc/init.d/network restart... (0 Replies)
Discussion started by: teis
0 Replies

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

5. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

6. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

7. Solaris

Unable to bring iscsitgt service to online

this is samiulla in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance and i am unable to bring into online with svcadm clear iscsitgt how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
3C589_CS(4)						     Kernel Interfaces Manual						       3C589_CS(4)

NAME
3c589_cs - 3Com 3c589 Etherlink III device driver SYNOPSIS
insmod 3c589_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...] DESCRIPTION
3c589_cs is the low-level Card Services driver for the 3Com 3c589 PCMCIA ethernet adapter and 3Com 3c562/3c563 combo cards. When this driver is attached to a card, it allocates the next available ethernet device (eth0..eth#). This device name will be reported in the ker- nel log file, and passed on to cardmgr(8). With the default transceiver setting, the driver will attempt to continuously autodetect the transceiver type (10base2 or 10baseT). There should normally only be a one or two second lag before the correct transceiver is selected. On particularly noisy or busy networks, it is possible for the detection logic to incorrectly toggle the transceiver type. If this becomes a problem, it may be necessary to explicitly select the interface type when the module is loaded or with the ifport command. PARAMETERS
pc_debug=n Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero value enables debugging. if_port=n Selects the transceiver type. 0 is autodetect (10baseT or 10base2), 1 is 10baseT (twisted pair), 2 is 10base2 (BNC, or thin net). and 3 is AUI (thick ethernet). The default is 0 (autodetect). irq_list=i,j,... Specifies the set of interrupts that may be allocated by this driver. DIAGNOSTICS
eth#: interrupt(s) dropped! Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi- cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration problem. AUTHOR
David Hinds - dahinds@users.sourceforge.net SEE ALSO
cardmgr(8), pcmcia(5), ifport(8). pcmcia-cs 2000/06/12 21:24:48 3C589_CS(4)
All times are GMT -4. The time now is 08:35 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy