09-20-2001
Hi alam,
What type of ethernet card have you got installed?
Also what error messages are being displayed when you attempt to bring up lo and eth0?
Andy H
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the... (2 Replies)
Discussion started by: mayewil
2 Replies
2. Solaris
Hello experts.
I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format.
Commands i used and output are....
#vxdisk list
DEVICE TYPE ... (11 Replies)
Discussion started by: younus_syed
11 Replies
3. IP Networking
Hi
(sorry for my bad English)
I'm trying to configure an US Robotics (USR5423) wirless usb adapter on Fedora 9. the device is detected, and i'm trying to configure a wireless connection.
When I want to activate the device using
#service network restart
or
# /etc/init.d/network restart... (0 Replies)
Discussion started by: teis
0 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. Solaris
this is samiulla
in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance
and i am unable to bring into online with svcadm clear iscsitgt
how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT SUSE
pppoe-sniff
PPPOE-SNIFF(8) System Manager's Manual PPPOE-SNIFF(8)
NAME
pppoe-sniff - examine network for non-standard PPPoE frames
SYNOPSIS
pppoe-sniff [options]
DESCRIPTION
pppoe-sniff listens for likely-looking PPPoE PADR and session frames and deduces extra options required for pppoe(8) to work.
Some DSL providers seem to use non-standard frame types for PPPoE frames, and/or require a certain value in the Service-Name field. It is
often easier to sniff those values from a machine which can successfully connect rather than try to pry them out of the DSL provider.
To use pppoe-sniff, you need two computers, a DSL modem and an Ethernet hub (not an Ethernet switch.)
If the DSL modem normally connects directly to your computer's Ethernet card, connect it to the "uplink" port on the Ethernet hub. Plug
two computers into normal ports on the hub. On one computer, run whatever software the DSL provider gave you on whatever operating system
the DSL provider supports. On the other computer, run Linux and log in as root.
On the Linux machine, put the Ethernet interface into promiscuous mode and start pppoe-sniff. If the ethernet interface is eth0, for exam-
ple, type these commands:
ifconfig eth0 promisc
pppoe-sniff -I eth0
On the other machine, start your DSL connection as usual. After a short time, pppoe-sniff should print recommendations for the value of
PPPOE_EXTRA. Set this value in /etc/ppp/pppoe.conf. If pppoe-sniff indicates that something special is required in PPPOE_EXTRA, please e-
mail this to pppoe@roaringpenguin.com along with the name of your ISP and the manufacturer and model number of your DSL modem. This infor-
mation will be collated and provided on the PPPoE web page for users who do not have two computers.
After pppoe-sniff finishes (or you stop it if it seems hung), remember to turn off promiscuous mode:
ifconfig eth0 -promisc
OPTIONS
-I interface
The -I option specifies the Ethernet interface to use. Under Linux, it is typically eth0 or eth1. The interface should be "up" and
in promiscuous mode before you start pppoe-sniff.
-V The -V option causes pppoe-sniff to print its version number and exit.
BUGS
pppoe-sniff only works on Linux.
AUTHORS
pppoe-sniff was written by David F. Skoll <dfs@roaringpenguin.com>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.
SEE ALSO
pppd(8), pppoe(8), pppoe-sniff(8), pppoe-relay(8), /usr/share/doc/pppoe/README.Debian.gz
4th Berkeley Distribution 3 July 2000 PPPOE-SNIFF(8)