04-29-2005
Let's say the hostname of your ss20 is server1 and the tape device is 0.
To backup all /opt files from server2 use server1:/dev/rmt/0n
# hostname
server2
# ufsdump 0cf server:/dev/rmt/0n /opt
See the man page for ufsdump (and/or tar) - a .rhosts file will be needed (I usually had one created via the scripts I ran just before the dump and then delete them afterwards as it is a security concern) along with the IP and host names in /etc/hosts for each server involved.
10 More Discussions You Might Find Interesting
1. Linux
All,
Has anybody ever got a Linux server to backup to a remote Solaris tape drive using the dump command and rsh? I can remtoely backup two Solaris server this way. Any help would be appreciated.
Thanks,
Mike (0 Replies)
Discussion started by: bubba112557
0 Replies
2. UNIX for Advanced & Expert Users
Hi,
OS: Solaris9, SPARC.
Commands (and their outputs) that I use to backup two files of size 4GB and 10GB (respectively) are shown below:
# cd /backup/daily/
# mt -f /dev/rmt/0m rew
# tar -cvf /dev/rmt/0m *
a Mails.bkf 4680454 tape blocks
a backup.bkf too large to archive
#
The... (3 Replies)
Discussion started by: mahatma
3 Replies
3. Shell Programming and Scripting
hi all,
very urgent need backup script on tape using solaris 8, my tape drive is DAT 72 on sun v240.
i need a simple script to backup files from directory /data/log/back/200703/filename.log. the files will backup continue each day on the tape which have 72 GB. the files size only 50MB and... (0 Replies)
Discussion started by: bucci
0 Replies
4. UNIX for Dummies Questions & Answers
Hi there: I'm new here
Can anyone help me:
I have DS15 Alpha server : Unix 5.1B
Now i need to connect a DLVT VS80 1U Rackmount Tape Drive unit.
What is the exact comman to mount the DLTape IV??
How do i make backuo @ copy file to the tape?
Thanx to all (0 Replies)
Discussion started by: ayzeayem
0 Replies
5. UNIX for Dummies Questions & Answers
Hi,
I performed backup on tape and I want to append more files to my previous backup on the same backup tape. But before I do that I need to know the backup file size of the first backup I performed so that I know the available size on the backup tape. Can someone help me what command I will use... (0 Replies)
Discussion started by: ayhanne
0 Replies
6. SCO
I am trying to make a full backup of my system using the cpio command. The Tape Unit is a SCSI DDS.
The process started fine but after about 30 minutes, it just stopped and showed the following message:
1755 Signal 31 - Core dumped
Any idea of what is causing this and how to fix it?
... (4 Replies)
Discussion started by: zionpc
4 Replies
7. UNIX for Dummies Questions & Answers
Hello everyone,
Just started UNIX today! In our school we use solaris. I just want to know how do I setup Solaris 10 not the GUI one, the one where you have to type the commands like ECHO, ls, pwd, etc... I have windows xp and I also have vmware.
I hope I am not missing anything! :p (4 Replies)
Discussion started by: Hanamachi
4 Replies
8. UNIX for Dummies Questions & Answers
Hi all
I had started to learn how to backup disk to disk to tape method
Firstly I had backup to my NAS
tar czvf /MyNetworkStorge/backup.tar /home
Secondly I using dd command to copy the tar to tape
dd if=/MyNetworkStorge/backup.tar of=/dev/tape0
But the tape drive always hang.... (5 Replies)
Discussion started by: lijiajin
5 Replies
9. Solaris
Hi,
I want to take backup of files older than 20 days from a directory onto a tape drive on remote machine on Solaris.
The files are of format abc-20100301000000.gz on my local machine.
I know the below commands for searching files older than x days and command for backup procedure.
solar1 #... (7 Replies)
Discussion started by: jyothi_wipro
7 Replies
10. Solaris
I am trying to restore opt on my server.
my issue is, all the partitions are saved into the same back up tape.
what is the exact command to just restore /opt for example, supposing c0t0d0s7 is the partition for /opt
---------- Post updated at 01:16 PM ---------- Previous update was at... (7 Replies)
Discussion started by: feg
7 Replies
LEARN ABOUT ULTRIX
ntp.conf
ntp.conf(5) File Formats Manual ntp.conf(5)
Name
ntp.conf - Network Time Protocol configuration file
Description
The file is the configuration file for the Network Time Protocol (NTP) daemon, This file must be configured on your system before running
Any host names that you specify in the file must have an entry in the file, or an entry in the master database, if the database is being
served to your system by BIND/Hesiod or Yellow Pages.
The file has four entry formats:
trusting no
This entry guarantees that your system synchronizes only to the NTP servers identified in the peer and server entries specified. Dig-
ital recommends that all systems include the entry.
peer server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system may also provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP servers should be configured with entries.
server server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system can not provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP clients should be configured with entries.
peer /dev/null LOCL 1 -5 local
This entry identifies your system as a local reference clock. A local reference clock is the most accurate system clock available at
your site. If you receive time synchronization from the Internet NTP service, you should not include this entry on any of your sys-
tems. At most, one system in a set of nodes running should be identified as a local reference clock.
A host which specifies this entry should not specify any or entries.
Examples
This is a sample configuration file for an NTP client which receives time synchronization from the NTP servers: and Lines beginning with a
number sign (#) are comments.
#
# NTP Configuration File
# This file is mandatory for the ntpd daemon
#
#
#
# ** A L L **
#
# "trusting no" prevents this host from synchronizing
# to any host that is not listed below. It is recommended
# that all hosts include the line "trusting no".
#
trusting no
#
#
# ** S E R V E R **
#
# If you are configuring a server, use "peer" entries to
# synchronize to other NTP servers. For example, server1,
# server2, and server3.
#
#peer server1
#peer server2
#peer server3
#
#
#
#
# ** C L I E N T **
#
# If you are configuring a client, use "server" entries to
# synchronize to NTP servers. For example, server1, server2,
# and server3.
#
server server1
server server2
server server3
#
#
#
# ** L O C A L R E F E R E N C E C L O C K **
#
# If you are configuring a local reference clock, include the
# following entry and the "trusting no" entry ONLY.
#
#peer /dev/null LOCL 1 -5 local
#
See Also
ntp(1), ntpd(8), ntpdc(8)
RFC 1129--Internet time synchronization: The Network Time Protocol
Introduction to Networking and Distributed System Services
ntp.conf(5)