How to put 2 IPs on a single NIC Post: 68585

9 More Discussions You Might Find Interesting

1. IP Networking

Can i put 2 ip address in one nic?

I have a SCO OpenServer 5.0.5 and my cuestion is can i have 2 ip address in one nic?, how?. Thanks.

2. Shell Programming and Scripting

How to put multiple logs in single line?

Hi, I have a script which generates a log file on demand by redirecting the output to a log file. But the requirement is : echo A echo B echo C should print A B C not like A B C and this has to be handled in script only..not in the shell level (while running the script only) ....

3. SCO

cannot put SCO 5.0.6 in single user mode

hi I have SCO 5.0.6 and if I type Ctrl-D, the system will NOT enter single user mode, it goes into multi-user mode. If I use the init 1 command, I get right back into the cycle ... an I'm at the Ctrl-D prompt again.

4. Programming

Macro to put single quotes around character

Dear Mates, I am trying to write a macro to replace with its arguments with singles quotes around each argument. #define DECR(a,b,c,d,e) decr('a','b','c','d','e') if the usage is DECR(k,e,y,s,\0) I want it to be replaced with the following decr('k','e','y','s','\0') However it...

5. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

6. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance!

7. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

8. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected...

9. UNIX for Advanced & Expert Users

Changing single path NIC to a teamed connection in same subnet

Dear all, I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths...

LEARN ABOUT DEBIAN

kumo-gateway

KUMO-GATEWAY(1) 					      General Commands Manual						   KUMO-GATEWAY(1)

NAME

       kumo-gateway - kumofs gateway daemon

SYNOPSIS

       kumo-gateway -m <addr[:port]> -p <addr[:port]> [-t port] [-b port] [-c port]

DESCRIPTION

       kumo-gateway  receives  requests  from applications and relays it to the kumo-servers.  Run this daemon on the hosts that runs applications
       that uses kumofs.

OPTIONS

       -m <addr[:port=19700]> --manager1
	      address of manager 1

       -p <addr[:port=19700]> --manager2
	      address of manager 2

       -lc --local-cache
	      local cache (Tokyo Cabinet abstract database)

       -t <[addr:]port=11411> --memproto-text
	      memcached text protocol listen port

       -b <[addr:]port=11511> --memproto-binary
	      memcached binary protocol listen port

       -c <[addr:]port=11611> --cloudy
	      asynchronous memcached binary protocol listen port

       -F --memproto-save-flag
	      save flags on memcached text protocol

       -As --async-replicate-set
	      send response without waiting replication on set

       -Ad --async-replicate-delete
	      send response without waiting replication on delete

       -G <number=5> --get-retry
	      get retry limit

       -S <number=20> --set-retry
	      set retry limit

       -D <number=20> --delete-retry
	      delete retry limit

       -rn <number=4> --renew-threshold
	      hash space renew threshold

       -k <number=2> --keepalive-interval
	      keepalive interval in seconds

       -Ys <number=1> --connect-timeout
	      connect timeout time in seconds

       -Yn <number=4> --connect-retry-limit
	      connect retry limit

       -Ci <number=2> --clock-interval
	      clock interval in seconds

       -TW <number=2> --write-threads
	      number of threads for asynchronous writing

       -TR <number=4> --read-threads
	      number of threads for asynchronous reading

       -o <path.log> --log
	      output logs to the file

       -g <path.mpac> --binary-log
	      enable binary log

       -v --verbose

       -d <path.pid> --daemon

EXAMPLE

       [on cli1  ]$ kumo-gateway -v -m mgr1 -p mgr2 -t 11211 -As -Ad

       [localhost]$ kumo-gateway -v -m localhost -t 11211 -d kumo-gateway.pid

SEE ALSO

       kumolog(1).

kumo-gateway							     July 2009							   KUMO-GATEWAY(1)