04-05-2005
Interface Details for HP-UX Box
Hi All,
I've recently been given an HP-UX Visualise J5600 to look after which runs our backup management software - it's connected to the network via 2 Gigabit Fibre channel cables.
Any ideas which command will give me the full connection details for those interfaces (and/or any others coming out the back of this box!) The card and slot details would be helpful as well as the ip addresses.
My concern is that although the ip address for the actual server is on one network, that at least one of the FC connections is assigned to a seperate VLAN (the backend network normally deals with the actual backup traffic) - would this be reflected in the answer to the above command or is there a seperate command to show all details of all interfaces?
(Moderators - I'm not sure if this is more a HP-UX question than a specific Dummies one so let me know if it needs to be posted elsewhere...)
Thanks for your help.
9 More Discussions You Might Find Interesting
1. Solaris
Given a new Solaris box, with a fresh, unconfigured install on it, how does one figure out what kind of network interface it has (bge,le, hme, etc)? (8 Replies)
Discussion started by: akbar
8 Replies
2. Solaris
Hi All,
I have an interface port configured to a FBOL server. This port receives requests from various hosts. I want to know at any moment of time ip addresses of all those hosts from which the requests are coming in. Please help me with command/script. (2 Replies)
Discussion started by: digitalrg
2 Replies
3. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
4. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
5. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. UNIX for Dummies Questions & Answers
I have scheduled couple of shell scripts to run using 'at' command.
The o/p of at -l is:
$ at -l
1320904800.a Thu Nov 10 01:00:00 2011
1320894000.a Wed Nov 9 22:00:00 2011
1320876000.a Wed Nov 9 17:00:00 2011
$ uname -a
SunOS dc2prcrptetl2 5.9 Generic_122300-54 sun4u sparc... (2 Replies)
Discussion started by: superparticle
2 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. Shell Programming and Scripting
Team,
Presently I have a script, which i have set up cron on one of my Jump-boxes,and gives me the output on every hourly basis,fetching the data from the remote machine.Basically it gives me the list of all active users logged and its count once we execute the script.Here the count is... (6 Replies)
Discussion started by: whizkidash
6 Replies
LEARN ABOUT CENTOS
ncftool
NCFTOOL(1) Network Configuration NCFTOOL(1)
NAME
ncftool - Network configuration tool
SYNOPSIS
ncftool [command [options]]
DESCRIPTION
ncftool is a command line utility to configure networking. It can be invoked with no arguments to bring up the interactive ncftool shell.
Alternatively a command and optional arguments can be specified to have ncftool execute the command non-interactively.
COMMANDS
list [--macs] [--all] [--inactive]
List the currently configured toplevel network interfaces
[--macs] - show MAC addresses
[--all] - show all (up & down) interfaces
[--inactive] - show only inactive (down) interfaces
dumpxml [--mac] [--live] name
Dump the XML description of an interface
[--mac] - interpret the name as MAC address
[--live] - include information about the live interface
name - the name of the interface
define xmlfile
Define an interface from the specified XML file.
undefine iface
Remove the configuration of the specified interface.
ifup iface
Bring up specified interface.
ifdown iface
Bring down specified interface.
change-begin
Mark the beginning of a set of revertible network configuration changes.
change-commit
Commit (make permanent) a set of network configuration changes begun with change-begin.
change-rollback
Rollback (revert) a set of network configuration changes begun with change-begin.
help [command]
Print details about command, if specified, or list all commands if command is not specified.
quit
Exit the program.
SEE ALSO
interfaces (5)
AUTHORS
Please refer to the AUTHORS file distributed with netcf.
netcf-0.2.2 2012-12-20 NCFTOOL(1)