03-31-2005
recovery partition table from fdisk?
I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk.
The possible reason could be:
1. I used default web start install. During the installation I didn't select the disk2. so I am not sure if solaris 8 will automatically erase the whole partition table on all disks in the system.
2. I did something like:
fdisk /dev/rdsk/c0t2d0s0 (the 2nd disk)
and answered 'yes' when it asked "type 'y' to accept the default partition. otherwise type 'n' to edit the partition table.
Now I guess 2 has caused the problem. and might have wiped out the partition table on the 2nd disk. Is there any way to recover it back? cuz the data are very important. I am a beginner in solaris. please offer your generous help here.
Thanks,
motor98
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Host 1
-------
Part Tag Flag Cylinders Size Blocks
0 root wm 0 - 1911 18.56GB (1912/0/0) 38913024
1 swap wu 1912 - 5434 34.19GB (3523/0/0) 71700096
2 backup wm 0 - 14086 136.71GB ... (5 Replies)
Discussion started by: sriny
5 Replies
2. UNIX for Dummies Questions & Answers
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (2 Replies)
Discussion started by: kevindoman
2 Replies
3. UNIX for Advanced & Expert Users
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (5 Replies)
Discussion started by: kevindoman
5 Replies
4. Filesystems, Disks and Memory
Hello,
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.
I want... (1 Reply)
Discussion started by: builder88
1 Replies
5. SCO
hi
How can I backup MBR an Partition Table of SCO 5.0.6? (7 Replies)
Discussion started by: ccc
7 Replies
6. Filesystems, Disks and Memory
Hi!
I have a really big problem right now. I (accidently) formatted a ext3 partition with "mkfs.ext3 /dev/sda1". The problem is that I REALLY need some files from there. The partition had a size of about 4GB, after accidently formatting it, I accidently rewrote Grub on it :wall: I hope I didn't... (3 Replies)
Discussion started by: al0x
3 Replies
7. Solaris
I'm preparing to recover a Oracle Fire X4170 server in a disaster recovery test at a different location than in prod. I have some questions about fdisk partitions. I'm using Solaris 10 update 10.
On my prod server, the boot disk has 2 partitions, diagnostic and solaris. Is the diagnostic... (1 Reply)
Discussion started by: TKD
1 Replies
8. Shell Programming and Scripting
Hi,
How can I run fdisk partition in a script without interactive input?
In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like... (3 Replies)
Discussion started by: hce
3 Replies
9. Red Hat
Hello,
I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies
10. BSD
Hello,
MBR partition table made by linux fdisk looks certainly not correct when printed by openbsd fdisk:
Partition table created on linux (centos 6.3):
# fdisk -l /dev/sdc
Disk /dev/sdc: 10.7 GB, 10737418240 bytes
255 heads, 63 sectors/track, 1305 cylinders
Units = cylinders of 16065 *... (2 Replies)
Discussion started by: vilius
2 Replies
LEARN ABOUT MINIX
repartit
REPARTITION(8) System Manager's Manual REPARTITION(8)
NAME
repartition - load a partition table
SYNOPSIS
repartition device [partition-file]
DESCRIPTION
Repartition uploads a new partition table for the partitions of device. The table is obtained from the first sector of partition-file if
given, device otherwise. Device may refer to the whole drive or a primary partition, depending on whether you want to upload a partition
or a subpartition table. The partitions will be truncated to fit within the enclosing device like the disk driver does, unless the numbers
are coming from partition-file.
EXAMPLES
repartition /dev/hd0
repartition /dev/hd4 /etc/hd4.table
Reload the partition table of drive 0 setting /dev/hd[1-4], and the subpartition table of /dev/hd4 setting /dev/hd4[a-d] using a file. The
latter may be useful if you need more than the 4 subpartitions a single Minix partition gives you.
DIAGNOSTICS
The new table is printed on standard output.
FILES
/dev/hd[0-9]
SEE ALSO
hd(4), part(8).
BUGS
The disk must be in use for the changes to stick. The partition table of an idle disk will be reloaded on the first open.
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
REPARTITION(8)