03-28-2005
Have a quick look in your other thread!!
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
Discussion started by: slacker
0 Replies
2. AIX
Hi,
I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1.
I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know... (7 Replies)
Discussion started by: bbbngowc
7 Replies
3. Solaris
Hi Gurus
Recently i had change the gateway for a server
i had change the IP in the /etc/defaultrouter
and run the below command
# route add default 10.86.33.222
# route delete default 10.86.33.1
# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref ... (2 Replies)
Discussion started by: SmartAntz
2 Replies
4. HP-UX
where in configuration files can i modify default gateway in hp-ux11iv3 (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
5. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. Red Hat
Hi..I have to change default gateway in my linux machine. Its OS is RHEL6.
I followed following steps.
1.run command ip route to check current default gateway
2.delete that gateway with command
route del default gw x.x.x.x eth2
3.Add new gatewy with command below
route add default gateway... (3 Replies)
Discussion started by: deljatt
3 Replies
8. IP Networking
I am am using IPv6 IP's with an OS of Debian.
Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected?
TIA (0 Replies)
Discussion started by: Meow613
0 Replies
9. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT MOJAVE
pthread_join
PTHREAD_JOIN(3) BSD Library Functions Manual PTHREAD_JOIN(3)
NAME
pthread_join -- wait for thread termination
SYNOPSIS
#include <pthread.h>
int
pthread_join(pthread_t thread, void **value_ptr);
DESCRIPTION
The pthread_join() function suspends execution of the calling thread until the target thread terminates unless the target thread has already
terminated.
On return from a successful pthread_join() call with a non-NULL value_ptr argument, the value passed to pthread_exit() by the terminating
thread is stored in the location referenced by value_ptr. When a pthread_join() returns successfully, the target thread has been terminated.
The results of multiple simultaneous calls to pthread_join() specifying the same target thread are undefined. If the thread calling
pthread_join() is cancelled, then the target thread is not detached.
RETURN VALUES
If successful, the pthread_join() function will return zero. Otherwise, an error number will be returned to indicate the error.
ERRORS
The pthread_join() function will fail if:
[EINVAL] The implementation has detected that the value specified by thread does not refer to a joinable thread.
[ESRCH] No thread could be found corresponding to that specified by the given thread ID, thread.
[EDEADLK] A deadlock was detected or the value of thread specifies the calling thread.
SEE ALSO
wait(2), pthread_create(3)
STANDARDS
The pthread_join() function conforms to ISO/IEC 9945-1:1996 (``POSIX.1'').
BSD
January 23, 2010 BSD