adding interfaces in solaris 9 Post: 67800

7 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Configuring networking interfaces on Solaris 10

Hi, I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command: #ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0 #add route or route add default xxx.xxx.xxx.xxx In Solaris 10, I believe the commands are...

2. Solaris

adding routes in Solaris

Solaris Guru's What is the proper way to add routes in the routing table so after a node reboot the routes will not be lost. I understand the /etc/defaultrouter for the default router and the <route add> command but using this command routes will be removed once the node reboots. Thanks

3. Solaris

Adding multiple virtual interfaces on a non global zone.

Hello All, I have a requirement to add multiple virtual interfaces on a non-global zone (Solaris 10). The global zone is a 2 node Veritas Cluster Server. So, my question is do we have to make any modifications to the cluster config (which I think should not be the case)? Can anyone help with me...

4. Solaris

Adding a user twice to Solaris OS

is it possible to add a user twice to solaris server with the same id? i have been added twice in the past week and that is messing up one application that i am using which authenticate against the os.

5. Solaris

Solaris 8: Multiple primary interfaces connected to the same network

Hello, I have a machine with Solaris 8, and it has multiple interfaces that are connected to the same network which means they all have metric 0 (1 hop) to the default gateway. assume: * e1000g0: 10.1.1.70 * e1000g2: 10.1.1.72 * e1000g4: 10.1.1.74 * e1000g5: 10.1.1.76 * gateway:...

6. Solaris

Interfaces and Virtual-interfaces queries

Hi Al, In course of understanding networking in Solaris, I have these doubts on Interfaces. Please clarify me. I have done fair research in this site and others but could not be clarified. 1. In the "ifconfig -a" command, I see many interfaces and their configurations. But I see many...

7. UNIX for Dummies Questions & Answers

Solaris Logic to transmit traffic to physical interfaces ( eg ce0 and ce1)

Just wanted to understand what is the logic being used by Solaris(kernel) to transmit data/traffic on physical interfaces. I have seen most of the time traffic is being sent to interface ce0 and sometime to ce1. I have removed ip address from below command for some reason. netstat -rn ...

LEARN ABOUT SUNOS

install-solaris

install-solaris(1M)													       install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris	invokes  the  Solaris  Install	program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

	   Minimum physical memory for all installation types

       128 MB

	   Minimum physical memory required for windowing system

       384 MB

	   Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

	   Minimum physical memory for all installation types

       256 MB

	   Minimum physical memory required for windowing system

       512 MB

	   Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris	exists	only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcdrom  (Solaris instal-  |
       |			     |lation media)		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

								    23 Sep 2005 					       install-solaris(1M)