03-26-2005
adding interfaces in solaris 9
Hi,
Have a solaris 9 e420, one onboard nic.
Now I added a quad nic card.
I have never had more than a single interface.
Any help on setting this new card up?
or links?
PLease? ; thanks!
7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
Discussion started by: annointed3
7 Replies
2. Solaris
Solaris Guru's
What is the proper way to add routes in the routing table so after a node reboot the routes will not be lost.
I understand the /etc/defaultrouter for the default router
and the <route add> command but using this command routes will be removed once the node reboots.
Thanks (7 Replies)
Discussion started by: Brad_52000
7 Replies
3. Solaris
Hello All,
I have a requirement to add multiple virtual interfaces on a non-global zone (Solaris 10). The global zone is a 2 node Veritas Cluster Server. So, my question is do we have to make any modifications to the cluster config (which I think should not be the case)? Can anyone help with me... (11 Replies)
Discussion started by: mahive
11 Replies
4. Solaris
is it possible to add a user twice to solaris server with the same id? i have been added twice in the past week and that is messing up one application that i am using which authenticate against the os. (10 Replies)
Discussion started by: basel
10 Replies
5. Solaris
Hello,
I have a machine with Solaris 8, and it has multiple interfaces that are connected to the same network which means they all have metric 0 (1 hop) to the default gateway.
assume:
* e1000g0: 10.1.1.70
* e1000g2: 10.1.1.72
* e1000g4: 10.1.1.74
* e1000g5: 10.1.1.76
* gateway:... (11 Replies)
Discussion started by: aeg
11 Replies
6. Solaris
Hi Al,
In course of understanding networking in Solaris, I have these doubts on Interfaces. Please clarify me. I have done fair research in this site and others but could not be clarified.
1. In the "ifconfig -a" command, I see many interfaces and their configurations. But I see many... (1 Reply)
Discussion started by: satish51392111
1 Replies
7. UNIX for Dummies Questions & Answers
Just wanted to understand what is the logic being used by Solaris(kernel) to transmit data/traffic on physical interfaces.
I have seen most of the time traffic is being sent to interface ce0 and sometime to ce1.
I have removed ip address from below command for some reason.
netstat -rn
... (3 Replies)
Discussion started by: nadeemahmed
3 Replies
LEARN ABOUT DEBIAN
ocf_heartbeat_viparip
OCF_HEARTBEAT_VIPARI(7) OCF resource agents OCF_HEARTBEAT_VIPARI(7)
NAME
ocf_heartbeat_VIPArip - Manages a virtual IP address through RIP2
SYNOPSIS
VIPArip [start | stop | monitor | meta-data | validate-all]
DESCRIPTION
Virtual IP Address by RIP2 protocol. This script manages IP alias in different subnet with quagga/ripd. It can add an IP alias, or remove
one.
SUPPORTED PARAMETERS
ip
The IPv4 address in different subnet, for example "192.168.1.1". (unique, required, string, no default)
nic
The nic for broadcast the route information. The ripd uses this nic to broadcast the route informaton to others (optional, string,
default eth0)
zebra_binary
Absolute path to the zebra binary. (optional, string, default /usr/sbin/zebra)
ripd_binary
Absolute path to the ripd binary. (optional, string, default /usr/sbin/ripd)
SUPPORTED ACTIONS
This resource agent supports the following actions (operations):
start
Starts the resource. Suggested minimum timeout: 20s.
stop
Stops the resource. Suggested minimum timeout: 20s.
monitor
Performs a detailed status check. Suggested minimum timeout: 20s. Suggested interval: 5s.
validate-all
Performs a validation of the resource configuration. Suggested minimum timeout: 20s.
meta-data
Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5s.
EXAMPLE
The following is an example configuration for a VIPArip resource using the crm(8) shell:
primitive p_VIPArip ocf:heartbeat:VIPArip
params
ip=string
op monitor depth="0" timeout="20s" interval="5s"
SEE ALSO
http://www.linux-ha.org/wiki/VIPArip_(resource_agent)
AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors)
resource-agents UNKNOWN 03/09/2014 OCF_HEARTBEAT_VIPARI(7)