03-26-2005
adding interfaces in solaris 9
Hi,
Have a solaris 9 e420, one onboard nic.
Now I added a quad nic card.
I have never had more than a single interface.
Any help on setting this new card up?
or links?
PLease? ; thanks!
7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
Discussion started by: annointed3
7 Replies
2. Solaris
Solaris Guru's
What is the proper way to add routes in the routing table so after a node reboot the routes will not be lost.
I understand the /etc/defaultrouter for the default router
and the <route add> command but using this command routes will be removed once the node reboots.
Thanks (7 Replies)
Discussion started by: Brad_52000
7 Replies
3. Solaris
Hello All,
I have a requirement to add multiple virtual interfaces on a non-global zone (Solaris 10). The global zone is a 2 node Veritas Cluster Server. So, my question is do we have to make any modifications to the cluster config (which I think should not be the case)? Can anyone help with me... (11 Replies)
Discussion started by: mahive
11 Replies
4. Solaris
is it possible to add a user twice to solaris server with the same id? i have been added twice in the past week and that is messing up one application that i am using which authenticate against the os. (10 Replies)
Discussion started by: basel
10 Replies
5. Solaris
Hello,
I have a machine with Solaris 8, and it has multiple interfaces that are connected to the same network which means they all have metric 0 (1 hop) to the default gateway.
assume:
* e1000g0: 10.1.1.70
* e1000g2: 10.1.1.72
* e1000g4: 10.1.1.74
* e1000g5: 10.1.1.76
* gateway:... (11 Replies)
Discussion started by: aeg
11 Replies
6. Solaris
Hi Al,
In course of understanding networking in Solaris, I have these doubts on Interfaces. Please clarify me. I have done fair research in this site and others but could not be clarified.
1. In the "ifconfig -a" command, I see many interfaces and their configurations. But I see many... (1 Reply)
Discussion started by: satish51392111
1 Replies
7. UNIX for Dummies Questions & Answers
Just wanted to understand what is the logic being used by Solaris(kernel) to transmit data/traffic on physical interfaces.
I have seen most of the time traffic is being sent to interface ce0 and sometime to ce1.
I have removed ip address from below command for some reason.
netstat -rn
... (3 Replies)
Discussion started by: nadeemahmed
3 Replies
LEARN ABOUT DEBIAN
opensc-tool
OPENSC-TOOL(1) OpenSC tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--info, -i
Print information about OpenSC, such as version and enabled components
--atr, -a
Print the Answer To Reset (ATR) of the card, output is in hex byte format
--name, -n
Print the name of the inserted card (driver)
--serial
Print the card serial number (normally the ICCSN), output is in hex byte format
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF...
--list-files, -f
Recursively lists all files stored on card
--list-readers, -l
Lists all configured readers
--list-drivers, -D
Lists all installed card drivers
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--wait, -w
Wait for a card to be inserted
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
SEE ALSO
opensc-explorer(1)
opensc 06/03/2012 OPENSC-TOOL(1)