03-18-2005
If you have a PCI/MCA card (HBA) properly installed into the device, then all the device attached to the 1st HBA (PCI/MCA) card would be listed as dka...and simillary for the other devices attached to the 2nd HBA (PCI/MCA) card will be lited as dkb. So, firstly ensure that you have devices installed properly. If you are sure that they are available, the try to run init again at the console and then try to list the devices attached with sho dev command ? Let me know. Can you give the list that you see on the console whe you run the show dev command?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I need to change the pka0_host_id 7 to 6 but the command "set pka0_host_id 6" returns "pka0_host_id protected from attempted operation".
How can i do that? please i need some answers soon!!!!! thanx (1 Reply)
Discussion started by: Lestat
1 Replies
2. HP-UX
I have a DS25 and when i run "show device" don't appear my 'dka.....' and 'dkb....' devices, but i know they must be there, where could be the error? what can i do to see them? (3 Replies)
Discussion started by: Lestat
3 Replies
3. UNIX for Advanced & Expert Users
I need to change the pka0_host_id 7 to 6 but the command "set pka0_host_id 6" returns "pka0_host_id protected from attempted operation".
How can i do that? please i need some answers soon!!!!! thanx (1 Reply)
Discussion started by: Lestat
1 Replies
4. UNIX for Dummies Questions & Answers
/dev/rmt/0: No such device or address
I get this when I do a "mt -f /dev/rmt/0 rewind"
This is on a Solaris 7 system.
I tried
devfsadm -c tape
and
drvconfig ; tape
and both didn't work.
Help please....... :confused: (4 Replies)
Discussion started by: shorty
4 Replies
5. Emergency UNIX and Linux Support
Dear All,
I was having powerpath 5.2 on SUN server with SVM connected to CLARIION box.Please find the following output :
root # powermt display dev=all
Pseudo name=emcpower3a
CLARiiON ID=CK200073400372
Logical device ID=60060160685D1E004DD97FB647BFDC11
state=alive; policy=CLAROpt;... (1 Reply)
Discussion started by: Reboot
1 Replies
6. Shell Programming and Scripting
Hi,
I am reading a directory that has a list of jar files. I am searching these files for specific keywords. What i would like to do is write the address of the jar file to a new file if the search result is returned as false. For example;
/home/user/JarDirectory/Examplefile.jar
... (2 Replies)
Discussion started by: crunchie
2 Replies
7. Shell Programming and Scripting
Hi,
I have line in input file as below:
3G_CENTRAL;INDONESIA_(M)_TELKOMSEL;SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL
My expected output for line in the file must be :
"1-Radon1-cMOC_deg"|"LDIndex"|"3G_CENTRAL|INDONESIA_(M)_TELKOMSEL"|LAST|"SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL"
Can someone... (7 Replies)
Discussion started by: shis100
7 Replies
8. UNIX for Dummies Questions & Answers
How to use "mailx" command to do e-mail reading the input file containing email address, where column 1 has name and column 2 containing “To” e-mail address
and column 3 contains “cc” e-mail address to include with same email.
Sample input file, email.txt
Below is an sample code where... (2 Replies)
Discussion started by: asjaiswal
2 Replies
9. Red Hat
Dear Concern,
We have observed that following command stuck/does not work in some RedHat nodes. Please advise us to troubleshoot the issue.
/usr/sbin/hpacucli ctrl all show
Note: HP Array Configuration Utility CLI for Linux 64-bit
With Best Regards,
Md. Abdullah-Al Kauser (3 Replies)
Discussion started by: makauser
3 Replies
10. UNIX for Beginners Questions & Answers
I am using the bash shell.
When I view my recent command history using the "history" command from the prompt, it only shows me the commands starting at #928.
The commands I need are earlier than that, but I can't figure out how to make the other 927 display.
They are in my .bash_history... (1 Reply)
Discussion started by: Twinklefingers
1 Replies
LEARN ABOUT REDHAT
memory_cb
MEMORY_CS(4) Kernel Interfaces Manual MEMORY_CS(4)
NAME
memory_cb - CardBus memory driver
SYNOPSIS
insmod memory_cb.o [pc_debug=n]
DESCRIPTION
Memory_cb gives direct memory access to the address spaces of CardBus cards. It provides character-mode devices for accessing a card's PCI
configuration space, up to six mapped memory or IO regions, and its expansion ROM space. When loaded, memory_cb will allocate a free major
device number. For each card, it will report which address spaces are available, and their sizes. Minor numbers have the form 'dddddsss',
where 'ddddd' is the instance number and 'sss' is the memory space for that instance. When memory_cb is bound to a card, it will report
its major and minor device numbers to cardmgr(8).
The default memory card initialization script creates device special files for all eight card address spaces, though for a particular card,
some of these may be unavailable. These devices have the following names:
/dev/cbmem#s0
The card's PCI configuration space.
/dev/cbmem#s[1-6]
The IO or memory spaces mapped by the card's six Base Address Registers.
/dev/cbmem#s7
The card's expansion ROM space.
The character special devices can be used to read and write arbitrary numbers of bytes to arbitrary locations. The memory_cb driver can be
bound to any card regardless of function.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5), memory_cs(4).
pcmcia-cs 2000/06/12 21:24:48 MEMORY_CS(4)