03-18-2005
If you have a PCI/MCA card (HBA) properly installed into the device, then all the device attached to the 1st HBA (PCI/MCA) card would be listed as dka...and simillary for the other devices attached to the 2nd HBA (PCI/MCA) card will be lited as dkb. So, firstly ensure that you have devices installed properly. If you are sure that they are available, the try to run init again at the console and then try to list the devices attached with sho dev command ? Let me know. Can you give the list that you see on the console whe you run the show dev command?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I need to change the pka0_host_id 7 to 6 but the command "set pka0_host_id 6" returns "pka0_host_id protected from attempted operation".
How can i do that? please i need some answers soon!!!!! thanx (1 Reply)
Discussion started by: Lestat
1 Replies
2. HP-UX
I have a DS25 and when i run "show device" don't appear my 'dka.....' and 'dkb....' devices, but i know they must be there, where could be the error? what can i do to see them? (3 Replies)
Discussion started by: Lestat
3 Replies
3. UNIX for Advanced & Expert Users
I need to change the pka0_host_id 7 to 6 but the command "set pka0_host_id 6" returns "pka0_host_id protected from attempted operation".
How can i do that? please i need some answers soon!!!!! thanx (1 Reply)
Discussion started by: Lestat
1 Replies
4. UNIX for Dummies Questions & Answers
/dev/rmt/0: No such device or address
I get this when I do a "mt -f /dev/rmt/0 rewind"
This is on a Solaris 7 system.
I tried
devfsadm -c tape
and
drvconfig ; tape
and both didn't work.
Help please....... :confused: (4 Replies)
Discussion started by: shorty
4 Replies
5. Emergency UNIX and Linux Support
Dear All,
I was having powerpath 5.2 on SUN server with SVM connected to CLARIION box.Please find the following output :
root # powermt display dev=all
Pseudo name=emcpower3a
CLARiiON ID=CK200073400372
Logical device ID=60060160685D1E004DD97FB647BFDC11
state=alive; policy=CLAROpt;... (1 Reply)
Discussion started by: Reboot
1 Replies
6. Shell Programming and Scripting
Hi,
I am reading a directory that has a list of jar files. I am searching these files for specific keywords. What i would like to do is write the address of the jar file to a new file if the search result is returned as false. For example;
/home/user/JarDirectory/Examplefile.jar
... (2 Replies)
Discussion started by: crunchie
2 Replies
7. Shell Programming and Scripting
Hi,
I have line in input file as below:
3G_CENTRAL;INDONESIA_(M)_TELKOMSEL;SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL
My expected output for line in the file must be :
"1-Radon1-cMOC_deg"|"LDIndex"|"3G_CENTRAL|INDONESIA_(M)_TELKOMSEL"|LAST|"SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL"
Can someone... (7 Replies)
Discussion started by: shis100
7 Replies
8. UNIX for Dummies Questions & Answers
How to use "mailx" command to do e-mail reading the input file containing email address, where column 1 has name and column 2 containing “To” e-mail address
and column 3 contains “cc” e-mail address to include with same email.
Sample input file, email.txt
Below is an sample code where... (2 Replies)
Discussion started by: asjaiswal
2 Replies
9. Red Hat
Dear Concern,
We have observed that following command stuck/does not work in some RedHat nodes. Please advise us to troubleshoot the issue.
/usr/sbin/hpacucli ctrl all show
Note: HP Array Configuration Utility CLI for Linux 64-bit
With Best Regards,
Md. Abdullah-Al Kauser (3 Replies)
Discussion started by: makauser
3 Replies
10. UNIX for Beginners Questions & Answers
I am using the bash shell.
When I view my recent command history using the "history" command from the prompt, it only shows me the commands starting at #928.
The commands I need are earlier than that, but I can't figure out how to make the other 927 display.
They are in my .bash_history... (1 Reply)
Discussion started by: Twinklefingers
1 Replies
ACPI(1) General Commands Manual ACPI(1)
NAME
acpi - Shows battery status and other ACPI information
SYNOPSIS
acpi [options]
DESCRIPTION
acpi Shows information from the /proc or the /sys filesystem, such as battery status or thermal information.
OPTIONS
-b | --battery
show battery information
-a | --ac-adapter
show ac adapter information
-t | --thermal
show thermal information
-c | --cooling
show cooling device information
-V | --everything
show every device, overrides above options
-s | --show-empty
show non-operational devices
-i | --details
show additional details if available:
* battery capacity information
* temperature trip points
-f | --fahrenheit
use fahrenheit as the temperature unit instead of default celsius
-k | --kelvin
use kelvin as the temperature unit instead of default celsius
-p | --proc
use the old /proc interface, default is the new /sys one
-d | --directory <dir>
path to ACPI info (either /proc/acpi or /sys/class)
-h | --help
display help and exit
-v | --version
output version information and exit
AUTHOR
The original version of this manual page was written by Paul Telford <pxt@debian.org> for the Debian system. Newer additions were done by
Michael Meskes <meskes@debian.org>. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU GPL.
ACPI(1)