03-17-2005
for i in `cat filename.txt`
do
grep $i /etc/passwd
etc
etc
done
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
At first, give my best wish for all MOD and admins here. I"m learning bash shell program just for a month, not too much, not too little, but i must admire that i'm very bad at math and algorithm. :(
I want to do this :
Read the content of a file line by line and at each line, ask me want to... (3 Replies)
Discussion started by: madi3d8
3 Replies
2. Shell Programming and Scripting
Hi,
I have gps receiver log..its giving readings .like below
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
GPSD,R=1
$GPGSV,3,1,11,08,16,328,40,11,36,127,00,28,33,283,39,20,11,165,00*71... (3 Replies)
Discussion started by: gudivada213
3 Replies
3. Shell Programming and Scripting
I am using the while-loop to read a file.
The file has lines with null-terminated strings (words, actually.)
What I have by that reading - just a first word up to '\0'!
I need to have whole string up to 'new line' - (LF, 10#10, 16#A)
What I am doing wrong?
#make file 'grb' with... (6 Replies)
Discussion started by: alex_5161
6 Replies
4. Shell Programming and Scripting
Hi,
i have file which contains data as below(Only sample shown, it may contain more data similar to the one shown here)
i need to read this file line by line and generate an output file like the one below
i.e based on N value the number of MSISDNs will vary, if N=1 then the following... (14 Replies)
Discussion started by: aemunathan
14 Replies
5. Shell Programming and Scripting
Hi ,
I am trying to write an shell, which reads a text file (from a location) having a list of numbers of strictly 5 digits only ex: 33144
Now my script will check :
1) that each entry is only 5 digits & numeric only, no alphabets, & its not empty.
2)then it executes a shell script called... (8 Replies)
Discussion started by: new_to_shell
8 Replies
6. Shell Programming and Scripting
Hello, I am quite new in shell scripting and I would like to write a little scritp to run a program on some parameters files.
all my parameters files are in the same directory, so pick them up with
ls *.para >>dirafter that I have a dir file like that:
param1.para
param2.para
etc...
I... (2 Replies)
Discussion started by: shadok
2 Replies
7. Shell Programming and Scripting
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
Discussion started by: mjavalkar
4 Replies
8. Shell Programming and Scripting
Hello,
I need a program that read a file line by line and prints out lines 1, 2 & 3 after an empty line... An example of entries in the file would be:
SRVXPAPI001 ERRO JUN24 07:28:34 1775
REASON= 0000, PROCID= #E506 #1065: TPCIPPR, INDEX= 003F
... (8 Replies)
Discussion started by: Ferocci
8 Replies
9. Shell Programming and Scripting
Hi All,
Am trying to write wrapper shell/bash script on a utility tool for which i need to pass 2 files as arugment to execute utility tool.
Wraper script am trying is to do with above metion 2 files.
utility tool accepts :
a. userinfo file : which contains username
b. item file : which... (2 Replies)
Discussion started by: Optimus81
2 Replies
10. Shell Programming and Scripting
Hi all,
I have a log file say Test.log that gets updated continuously and it has data in pipe separated format. A sample log file would look like:
<date1>|<data1>|<url1>|<result1>
<date2>|<data2>|<url2>|<result2>
<date3>|<data3>|<url3>|<result3>
<date4>|<data4>|<url4>|<result4>
What I... (3 Replies)
Discussion started by: pat_pramod
3 Replies
LEARN ABOUT DEBIAN
unbuffer
UNBUFFER(1) General Commands Manual UNBUFFER(1)
NAME
unbuffer - unbuffer output
SYNOPSIS
unbuffer program [ args ]
INTRODUCTION
unbuffer disables the output buffering that occurs when program output is redirected from non-interactive programs. For example, suppose
you are watching the output from a fifo by running it through od and then more.
od -c /tmp/fifo | more
You will not see anything until a full page of output has been produced.
You can disable this automatic buffering as follows:
unbuffer od -c /tmp/fifo | more
Normally, unbuffer does not read from stdin. This simplifies use of unbuffer in some situations. To use unbuffer in a pipeline, use the
-p flag. Example:
process1 | unbuffer -p process2 | process3
CAVEATS
unbuffer -p may appear to work incorrectly if a process feeding input to unbuffer exits. Consider:
process1 | unbuffer -p process2 | process3
If process1 exits, process2 may not yet have finished. It is impossible for unbuffer to know long to wait for process2 and process2 may
not ever finish, for example, if it is a filter. For expediency, unbuffer simply exits when it encounters an EOF from either its input or
process2.
In order to have a version of unbuffer that worked in all situations, an oracle would be necessary. If you want an application-specific
solution, workarounds or hand-coded Expect may be more suitable. For example, the following example shows how to allow grep to finish pro-
cessing when the cat before it finishes first. Using cat to feed grep would never require unbuffer in real life. It is merely a place-
holder for some imaginary process that may or may not finish. Similarly, the final cat at the end of the pipeline is also a placeholder
for another process.
$ cat /tmp/abcdef.log | grep abc | cat
abcdef
xxxabc defxxx
$ cat /tmp/abcdef.log | unbuffer grep abc | cat
$ (cat /tmp/abcdef.log ; sleep 1) | unbuffer grep abc | cat
abcdef
xxxabc defxxx
$
BUGS
The man page is longer than the program.
SEE ALSO
"Exploring Expect: A Tcl-Based Toolkit for Automating Interactive Programs" by Don Libes, O'Reilly and Associates, January 1995.
AUTHOR
Don Libes, National Institute of Standards and Technology
1 June 1994 UNBUFFER(1)