08-31-2001
lm_sensors? hardware monitoring?
ok ok ok, this is my third post on the day I become a member. I should stop. I'm sure all my questions are in the wrong forums. I'm sorry.
my question is about lm_sensors, and hardware monitoring.
I have the goods, lm_sensors.tar.gz, and i2c.tar.gz
and I'm rather confusled. could someone please hold my hand through this? I need someone with some experience with hardware monitoring...
or something.
thanks
5 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I was given the task to write a shell script that must detect hardware problems on Unix Solaris and AIX servers. Problems that should be detected by this script are for example: abnormally high temperature or voltage etc...
So, does anyone know if that kind of information is logged in a... (2 Replies)
Discussion started by: VeroL
2 Replies
2. AIX
Hello again,
I would like to know if the following commands:
diag, errpt, lscfg, lspv, lsvg, lsps, lslv for AIX and
prtdiag, psrinfo, sysdef for SUN are native to these systems or if they are in fact scripts that are added after the unix installation.
Thank you in advance.
Have a nice day (4 Replies)
Discussion started by: VeroL
4 Replies
3. UNIX for Dummies Questions & Answers
Folks;
What is a good free tool i can use on my SUSE10 to monitor the hardware so i can be notified in case of any failure such as fan failure, etc..? (2 Replies)
Discussion started by: Katkota
2 Replies
4. Shell Programming and Scripting
Gentlemen
I want to write a small script and run as cronjob sothat the script runs every four hours
The script should be capable of finding any hardware issues,panics,coredumps
if anyissues found it should sent mail.If no issues it shouldnt sent mail
Deeply appreciated if any help... (2 Replies)
Discussion started by: saidiya
2 Replies
5. Windows & DOS: Issues & Discussions
:wall:hi all, as hp support pack has hpasm, hpacu command using in linux server to show and monitor hareware status.
hpacu command was avaialbe in windows server also, but where can find hpasm command in windows, it looks hp support pack not support hpasm in windows. any one can help? an... (1 Reply)
Discussion started by: maxlee24
1 Replies
sensors(1) Linux User's Manual sensors(1)
NAME
sensors - print sensors information
SYNOPSIS
sensors [ options ] [ chips ]
sensors -s [ chips ]
sensors --bus-list
DESCRIPTION
sensors is used to show the current readings of all sensor chips.
sensors -s is used to set all limits as specified in the configuration file.
sensors --bus-list is used to generate bus statements suitable for the configuration file.
OPTIONS
-c config-file
Specify a configuration file. If no file is specified, the libsensors default configuration file is used. Use `-c /dev/null' to tem-
porarily disable this default configuration file.
-h Print a help text and exit.
-s Evaluate all `set' statements in the configuration file and exit. You must be `root' to do this. If this parameter is not specified,
no `set' statement is evaluated.
-A Do not show the adapter for each chip.
-u Raw output. This mode is only meant for debugging.
-v Print the program version and exit.
-f Print the temperatures in degrees Fahrenheit instead of Celsius.
--bus-list
Generate bus statements suitable for using in sensors.conf. Such bus statements are only needed if you have several chips sharing
the same address on different buses of the same type. As bus numbers are usually not guaranteed to be stable over reboots, these
statements let you refer to each bus by its name rather than numbers.
FILES
/etc/sensors3.conf
/etc/sensors.conf
The system wide configuration file. See sensors.conf(5) for further details.
SEE ALSO
sensors.conf(5)
AUTHOR
Frodo Looijaard and the lm_sensors group http://www.lm-sensors.org/
lm-sensors 3 October 2007 sensors(1)