02-01-2005
System crash and Disk erasure !!!
I need some expert help, and would appreciate any feedback on the following problem:
After power outage the machine didn't allow the login. When we checked it , it looked like both disks were completely empty. Luckily, we have a backup machine, and we can restore the disks.
Has anybody seen anything like this before ?
What could cause such a dramatic outcome, and what can be done to prevent further problems ?
I have no clue where I can start looking for explanation. So maybe somebody could help me which files I could take a look at and what are the best steps to perform in my situation ?
Thanks in advance,
Regards
Dennis
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We have a Unix system with two hard drives. When we tried to access it this morning it had frozen, and when we rebooted it couldn't find one of the hard drives, and had quite a few bad data blocks on the other. Of course we fear the worst: that the drive is completely gone, but were not sure how... (1 Reply)
Discussion started by: Kgatliffe
1 Replies
2. UNIX for Dummies Questions & Answers
Hello All
We are using Tru64 Unix V4.0D on a Digital Alpha 1200 machine, which by coincidence, crashed last night! Completely out of the Blue!!! After rebooting the system and recovering the databases everything seemed to work ok. It is however, discomforting not to know how or why the system... (2 Replies)
Discussion started by: Ivo
2 Replies
3. HP-UX
Hi,
First of all, thanks for your help. I have downloaded freeBSD to study unix
I'm here again 'cause my HP-UX 10.x has "broken". It raise this error:
----------------------------------------------------
Diagnostic System warning:
= 0x1f005000 is POWERFAILED The diagnostic logging... (1 Reply)
Discussion started by: efrenba
1 Replies
4. UNIX for Dummies Questions & Answers
helo,
suppose u have well build in product system which is build in linux o.s. now due to reason system automatically become crash(software crash),then how do u handle such crash. which is better way to handle such crash.
amit (0 Replies)
Discussion started by: amitpansuria
0 Replies
5. Filesystems, Disks and Memory
Hi, First post. I am not to experienced in the Unix or HP-UX world but I'm learning.
We have some problem with a HP rx4640 server. During boot it states the following:
Checking for LVM volume groups and Activating (if any exist)
Volume group "/dev/vg00" has been successfully changed.
vgchange:... (7 Replies)
Discussion started by: hoff
7 Replies
6. AIX
Hello everyone
I have a partition with the TL 5300-06-01-0000 and try to update to this TL 5300-09-03-0918 but suddenly the update dont work more. I get in to the HMC and I see this code error 888 102 700 0C5
I try to restart my partition but doesnt work.
Theres someone who has this... (9 Replies)
Discussion started by: lo-lp-kl
9 Replies
7. Solaris
Hi all,
I want to put a local disk on a Sun Cluster node but scconf command explodes :eek:
My system:
* two node cluster on two VMWare virtual machines
* Solaris 10 SunOS 5.10 Generic_141415-05 i86pc i386 i86pc
* Sun Cluster 3.2 u2
* Veritas Volume manager
The situation... (2 Replies)
Discussion started by: gxmsgx
2 Replies
8. UNIX for Dummies Questions & Answers
Hi all,
First and foremost I would like to mention I am pretty new to Linux.
I have some experience in Windows systems administration but nothing professionally.
Expect some real newbie questions.
For a small company I am trying to install a server so a development environment can be... (1 Reply)
Discussion started by: Crazy Harry
1 Replies
9. HP-UX
Hi all,
I have a server running HP-UX 11i V1 (11.11).
We had a problem with the system disk which cannot boot and the recovery with the CD failed too.
the only solution was to re-install the system on a new disk.
The problem now is to get access to the data which are on other disks, not... (2 Replies)
Discussion started by: aribault
2 Replies
10. Solaris
Hello all;
We have a SunFire V240 with three disks that were part of a metadb. One of those disks, the boot disk, experienced a horrible death Monday night and we're now trying to recover from that.
I know very little about metadb stuff, so please be gentle with me...
I'm assuming... (3 Replies)
Discussion started by: Handon
3 Replies
LEARN ABOUT MOJAVE
vgreduce
VGREDUCE(8) System Manager's Manual VGREDUCE(8)
NAME
vgreduce - reduce a volume group
SYNOPSIS
vgreduce [-a|--all] [-A|--autobackup y|n] [-d|--debug] [-h|-?|--help] [--removemissing] [-t|--test] [-v|--verbose] VolumeGroupName [Physi-
calVolumePath...]
DESCRIPTION
vgreduce allows you to remove one or more unused physical volumes from a volume group.
OPTIONS
See lvm for common options.
-a, --all
Removes all empty physical volumes if none are given on command line.
--removemissing
Removes all missing physical volumes from the volume group, if there are no logical volumes allocated on those. This resumes normal
operation of the volume group (new logical volumes may again be created, changed and so on).
If this is not possible (there are logical volumes referencing the missing physical volumes) and you cannot or do not want to remove
them manually, you can run this option with --force to have vgreduce remove any partial LVs.
Any logical volumes and dependent snapshots that were partly on the missing disks get removed completely. This includes those parts
that lie on disks that are still present.
If your logical volumes spanned several disks including the ones that are lost, you might want to try to salvage data first by acti-
vating your logical volumes with --partial as described in lvm (8).
SEE ALSO
lvm(8), vgextend(8)
Sistina Software UK LVM TOOLS 2.02.95(2) (2012-03-06) VGREDUCE(8)