01-26-2005
Hi,
it is the primary OS boot disk, and using dd on linux is a bit critical. The systems I wnt to mirror, are mostly NFS Fileservers. The dd command forces the linux system to flush all dirty pages, you can imagine what happens in that situation with the system
It stalls ...
Therefore, I can everything except dd
But dd was also my first idea, until this experience...
I already did some testings with rsync and it looks not so bad ..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can anyone give some answers on what is disk mirroring in Unix? It may be related to unix online backup. (2 Replies)
Discussion started by: asutoshch
2 Replies
2. Filesystems, Disks and Memory
After reading some books, I came across this idea of having a duplicate of your current hard drive on another second hard drive so that if the first hard drive happens to crash, the system can be up and running in quickly
now, is there anybody in here who uses this method at work?? If there is,... (3 Replies)
Discussion started by: IMPORTANT
3 Replies
3. UNIX for Dummies Questions & Answers
I would like to build a new box that has the disk mirrored to another IDE disk on a different channel. Does anyone know if a RAID controller like the Promise is supported under RedHat 8, or should I use a software RAID. (1 Reply)
Discussion started by: 98_1LE
1 Replies
4. Solaris
Hi
I have two raw disk that I want to mirror and then create soft partition on that. Could someone please help in the steps required
c0t1d0
c0t0d0
Thanks
Ajwat (2 Replies)
Discussion started by: Ajwat
2 Replies
5. Solaris
Hi
I have a Sunfire X4100 box with a 4 disk Chassis (although I only have 2 disks in it). I have been asked to add two more disks into the chassis so that I can mirror the original two using SVM .....Ive read through a couple of SVM docs but am finding it a little confusing, and if any of you... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
6. UNIX for Advanced & Expert Users
How can one mirror disk geometry from one hard disk to another in Solaris.
Is disk snapshot same as a mirror? Pls explain. (3 Replies)
Discussion started by: lexusujx
3 Replies
7. Solaris
Has anyone managed to set up disk mirroring in Solaris 10 yet? If so can you point me in the direction of some useful documentation please.
Cheers (25 Replies)
Discussion started by: korfnz
25 Replies
8. Solaris
Hi Friends,
I am having Sun Solaris 5.8 OS installed having 2 different size hard disk, sizes are c0t0d0s0(160 GB) and c0t2d0s0 (40GB). I have installed Sun Solaris 5.8 OS in c0t0d0s0 (160GB) harddisk.
I have configured all the parameters required for disk mirroring. But when executing... (4 Replies)
Discussion started by: Vijayakumarpc
4 Replies
9. Solaris
hi every body
I'm new to solaris and I need your help in how to configure disk mirroring for 4 hard disks so that two of them will be replica to the other two ...???
Thanxx (7 Replies)
Discussion started by: mm00123
7 Replies
10. Red Hat
Hi,
How to identify whether the disk is being mirrored or not in RHEL (2 Replies)
Discussion started by: gsiva
2 Replies
LEARN ABOUT LINUX
mkfs.minix
MKFS.MINIX(8) Linux System Administrator's Manual MKFS.MINIX(8)
NAME
mkfs.minix - make a Linux MINIX filesystem
SYNOPSIS
mkfs.minix [-c|-l filename] [-n namelength] [-i inodecount] [-v] device [size-in-blocks]
DESCRIPTION
mkfs.minix creates a Linux MINIX file-system on a device (usually a disk partition).
The device is usually of the following form:
/dev/hda[1-8] (IDE disk 1)
/dev/hdb[1-8] (IDE disk 2)
/dev/sda[1-8] (SCSI disk 1)
/dev/sdb[1-8] (SCSI disk 2)
The size-in-blocks parameter is the desired size of the file system, in blocks. It is present only for backwards compatibility. If omit-
ted the size will be determined automatically. Only block counts strictly greater than 10 and strictly less than 65536 are allowed.
OPTIONS
-c Check the device for bad blocks before creating the file system. If any are found, the count is printed.
-n namelength
Specify the maximum length of filenames. Currently, the only allowable values are 14 and 30. The default is 30. Note that kernels
older than 0.99p7 only accept namelength 14.
-i inodecount
Specify the number of inodes for the filesystem.
-l filename
Read the bad blocks list from filename. The file has one bad block number per line. The count of bad blocks read is printed.
-v Make a Minix version 2 filesystem.
EXIT CODES
The exit code returned by mkfs.minix is one of the following:
0 No errors
8 Operational error
16 Usage or syntax error
SEE ALSO
mkfs(8), fsck(8), reboot(8)
AVAILABILITY
The mkfs.minix command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
Util-linux 2.6 2 July 1996 MKFS.MINIX(8)