Sponsored Content
Top Forums Programming Joining multicast group on IPADDR_ANY - which interface? Post 60638 by Neo on Wednesday 19th of January 2005 05:51:38 PM
Old 01-19-2005
The interface is chosen using the IP routing table.
 

8 More Discussions You Might Find Interesting

1. HP-UX

How to multicast on different IP network

Hi, there On HP-UX, I want to multicast packets on two different IP network repectively. The two NIC are configured with two different IP. The routes are added with one default and one net for each IP . The multisender programs bind their own local IP, multireceiver programs add the... (0 Replies)
Discussion started by: Frank2004
0 Replies

2. Linux

How to multicast on different IP network

On Linux, I have configured two different IP address for two network device eth0 ,eth1 , in my program, I want to multicast differently on these two network, I know it must add route for single network and I try to config another route for second network,but it can not work correctly, how to config... (0 Replies)
Discussion started by: Frank2004
0 Replies

3. Solaris

multicast config

On SUN Solaris 10, if I want to multicast packets between nodes, whether it must config the multicast IP from OS, if yes, how to do it? (0 Replies)
Discussion started by: Frank2004
0 Replies

4. Solaris

Reboot, System is Frozen at setting interface for multicast HELP

I'm not an advanced user by any strech, that being said here is my problem: I ran "reboot" on a sun blade 2500 When loading up it runs through the usual routine, checking disks, filesystems and then it locks up after the following message: ***** starting rpc services: rpcbind... (6 Replies)
Discussion started by: eyukins
6 Replies

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

7. Shell Programming and Scripting

Joining multi-line output to a single line in a group

Hi, My Oracle query is returing below o/p ---------------------------------------------------------- Ins trnas value a lkp1 x a lkp1 y b lkp1 a b lkp2 x b lkp2 y ... (7 Replies)
Discussion started by: gvk25
7 Replies

8. IP Networking

Multicast IP address

Hi please help, theoretically I',m interested in starting a streaming service using multicast IP service. I'd like to know how do I get an IP address that I can send my data too? (please don't just point me too Internet Assigned Numbers Authority as ive been there and it just seem to state... (1 Reply)
Discussion started by: fishman2001
1 Replies
NRBROADCAST(5)						     Linux Programmer's Manual						    NRBROADCAST(5)

NAME
nrbroadcast - NET/ROM routing broadcast configuration file. DESCRIPTION
Nrbroadcast is an ASCII file that contains information about each of the physical AX.25 ports that are to have NET/ROM routing broadcasts transmitted from them. Each line has the following format, each field being delimited by white space: port minobs defqual worstqual verbose The field descriptions are: port the port name of the AX.25 port to broadcast on. minobs this is the minimum obsolescence count of a routing table entry to be broadcast on this port. defqual this is the default quality of an incoming routing broadcast from an unknown neighbour. worstqual this is the worst quality node received from a routing broadcast that will be added to our routing table. verbose whether the routes to all of my nodes in my routing table, or just the nodes resident on my machine are to be broad- cast. FILES
/etc/ax25/nrbroadcast /etc/ax25/axports SEE ALSO
call(1), netrom(4), axports(5), netromd(8), nrparms(8). Linux 2 August 1996 NRBROADCAST(5)
All times are GMT -4. The time now is 09:17 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy