Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Adding a Unix Server to a Windows 2000 Network Post 59584 by zazzybob on Thursday 23rd of December 2004 08:59:46 AM
Old 12-23-2004
The easiest way to see if the IP address, etc, is configured is via ifconfig.

Type
man ifconfig
to read the manual page for ifconfig, as each *nix has its own command variation.

The actual interface device name also varies wildly between unix flavours. You can run

ifconfig <device>

Linux uses eth0 for the first ethernet device
HP-UX uses lan0
And SCO (I believe) uses net0

On SCO, ifconfig -a will show you information about all configured devices

*something like*
ifconfig net0 192.168.0.1 netmask 255.255.255.0 up
should bring the interface up if it already isn't.

You'll then need
route add default 192.168.0.100

to specify the default gateway
(Linux uses "route add default gw <address>")

All this will need to be added to startup scripts to make the changes persistent after everything is tested and working.

You'll also need to think about DNS, or if your network only has a few hosts on it, just edit the /etc/hosts file and add the hosts in.

There's quite a lot to do, and there is some good documentation on www.sco.com

Cheers
ZB
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Unix with Windows 2000

Hey! I have just acquired a Unisys SMP6400 server. It has Unix already installed. It has 2 disk drives: 1 is 2 gig with Unix setup on it. The 2nd drive is 8 gig with apps. Both drives are under Mylex DAC960 raid control. Here is my question, can I install Windows 2000 Pro on this machine either... (11 Replies)
Discussion started by: mastermold
11 Replies

2. UNIX for Dummies Questions & Answers

Sco openserver and Windows 2000 server

Hi, i have 4 Unix Sco openservers, 4PCs running windows 2000, and 1 PC with windows server which i want to configure in the same network. During the configuration procedure, the wizard of Windows 2000 SERVER ask you if this is the only server in the network, now it will be the only WINDOWS... (2 Replies)
Discussion started by: BAM
2 Replies

3. Cybersecurity

permissions and security with windows 2000 server

I setup a Windows 2000 Server so that a G4 could access one specific folder. The only way this contact could take place between the two operating systems is with Maclan. I have not installed it with the PCmaclan currently, I have only been reading about it. Can someone assist me with this... (0 Replies)
Discussion started by: pmoncriffe
0 Replies

4. Solaris

setting up unix and 2000 server on network

i have a question i want to setup a unix server and 2000 server with an xp client i want to run bind can i still setup a primary dns on the 2000 box or can u use secondary dns on 2000 also i want to setup an exchange server on the 2000 server for email between the windows machines? basically i... (2 Replies)
Discussion started by: rmuhammad
2 Replies

5. UNIX for Dummies Questions & Answers

Adding MS 2000 FSMO Roles to Unix Bind

In a Windows 2000 active directory environment (using Unix DNS), is it possible to create entries in Unix Bind to point Microsoft Workstations to specific Microsoft servers, depending on their Microsoft FSMO roles (i.e. Domain Naming Master, PDC Emulator, RID, Infrastructure Master)? In other... (0 Replies)
Discussion started by: breffkin
0 Replies

6. Windows & DOS: Issues & Discussions

file management in windows 2000 server

i am using windows 2000 server. my query is as follows: there are 2 directories say c:\emp & c:\exe. DataBase (DB) files are there in emp folder and the executables are in exe folder. Now i want to share the exe folder to the clients. If i give read permission to the exe folder and no... (3 Replies)
Discussion started by: raguramtgr
3 Replies

7. UNIX for Dummies Questions & Answers

Unix in Network 2000 Server

Hi, is it possible to see our Unix server, with logged-on users(for that specifiek unix-network domain) in my network environment, on my xp pc (i however, log on at our 2000 server)? We have a windows2000 server and both are connected in our LAN. Do i need to make a trust relationship or do i have... (0 Replies)
Discussion started by: devuyst
0 Replies

8. Shell Programming and Scripting

SFTP from UNIX (AIX) to Windows 2000 server

Hi all, I have to sftp a file (put) from AIX server to Windows 2000 server. The question is Windows 200 server that i am using doesnt have any SFTP server , if so i know we need to install one. The question here is for writing a sftp script that as to run everyday as part of cron job we... (0 Replies)
Discussion started by: reddymails
0 Replies

9. Windows & DOS: Issues & Discussions

restart windows 2000 server using command line

Hi all expert, Anybody know how to restart the windows 2000 server through command line and without using any additional tool? Thanks :):) (2 Replies)
Discussion started by: wilsonSurya
2 Replies
cupsaddsmb(8)						      Easy Software Products						     cupsaddsmb(8)

NAME
cupsaddsmb - export printers to samba for windows clients SYNOPSIS
cupsaddsmb [ -H samba-server ] [ -U samba-user ] [ -h cups-server ] [ -v ] -a cupsaddsmb [ -H samba-server ] [ -U samba-user ] [ -h cups-server ] [ -v ] printer [ ... printer ] DESCRIPTION
cupsaddsmb exports printers to the SAMBA software (version 2.2.0 or higher) for use with Windows clients. Depending on the SAMBA configura- tion, you may need to provide a password to export the printers. This program requires the CUPS or Adobe PostScript printer driver files described below. The -H option specifies the SAMBA server which defaults to the CUPS server. The -U option specifies the SAMBA print admin username which defaults to your current username. The -a option exports all known printers. Otherwise only the named printers are exported. The -h option specifies a different CUPS server to use. The -v option specifies that verbose information should be shown and is useful for debugging SAMBA configuration problems. SAMBA CONFIGURATION
cupsaddsmb uses the new RPC-based printing support in SAMBA 2.2.x to provide printer drivers and PPD files to Windows client machines. In order to use this functionality, you must first configure SAMBA (via the smb.conf file) to support printing through CUPS and provide a printer driver download share, as follows: [global] load printers = yes printing = cups printcap name = cups [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes guest ok = yes writable = no printable = yes printer admin = root [print$] comment = Printer Drivers path = /etc/samba/drivers browseable = yes guest ok = no read only = yes write list = root This configuration assumes a FHS-compliant installation of SAMBA; adjust the [printers] and [print$] share paths accordingly on your system as needed. CUPS POSTSCRIPT DRIVERS FOR WINDOWS
cupsaddsmb can use the CUPS PostScript printer drivers for Windows, which are available for download from the CUPS web site. The CUPS printer drivers are preferred over the Adobe drivers since they support page accounting, banner pages, and page labels on all printers. However, currently only Windows NT, 2000, and XP are supported by the CUPS drivers, so you will also need to get the Adobe driver to support Windows 95, 98, and Me clients. Once you have extracted the driver files, create a "drivers" directory in the CUPS data directory (usually /usr/share/cups) and copy the CUPS files using lowercase filenames, as follows: [Windows NT, 2000, and XP] cups.hlp cupsdrvr.dll cupsui.dll ADOBE POSTSCRIPT DRIVERS FOR WINDOWS
cupsaddsmb can use the Adobe PostScript printer drivers for Windows, which are available for download from the Adobe web site (http://www.adobe.com). The CUPS printer drivers are preferred over the Adobe drivers since they support page accounting, banner pages, and page labels on all printers. Once you have extracted the driver files, create a "drivers" directory in the CUPS data directory (usually /usr/share/cups) and copy the Adobe files using UPPERCASE filenames, as follows: [Windows 95, 98, and Me] ADFONTS.MFM ADOBEPS4.DRV ADOBEPS4.HLP DEFPRTR2.PPD ICONLIB.DLL PSMON.DLL [Windows NT, 2000, and XP] ADOBEPS5.DLL ADOBEPSU.DLL ADOBEPSU.HLP You can download and copy either set of driver files independently, and use the CUPS drivers for Windows NT, 2000, and XP while using the Adobe drivers for the Windows 95, 98, and Me clients. SEE ALSO
CUPS Software Administrators Manual, http://localhost:631/documentation.html COPYRIGHT
Copyright 1993-2002 by Easy Software Products, All Rights Reserved. 27 September 2002 Common UNIX Printing System cupsaddsmb(8)
All times are GMT -4. The time now is 11:32 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy