12-18-2004
dhcp command in FreeBSD?
Is there a dhcp command in FreeBSD 5.3? I know in Linux, there was a command "dhcpcd" that I had to use in order for my WiFi NIC to get all the information that it needed. Is there something similar to this? Thanks.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi you all. I'm trying to enable DHCP in a Sun Utra 5 runing Solaris 8 but during the boot process it sends me the message : "Device not in appropiate status"
Do anyone have enabled DHCP on solaris 8?
Any Procedure?
The DHCP server is an NT I guess. (2 Replies)
Discussion started by: alex blanco
2 Replies
2. IP Networking
I'm trying to make a transition from linux to unix, but one of the major hang ups is my networked internet connection.
(1) Cable Internet (Adelphia)
(2) Modem -> Cat5
(3) Cat5 -> D-Link Router
(4) D-Link Router -> Cat5
(5) Cat5 -> D-Link 10/100 Ethernet/USB Adapter
On boot it says it sees... (1 Reply)
Discussion started by: xviddivxoggmp3
1 Replies
3. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
4. IP Networking
can I request for an ipaddress through dhcp client by sending ipaddress as input during the invokation of dhcpclient so that it requests the server for the same,instead of depending on the configuration file . (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
5. IP Networking
So I'm trying to work with a Linux box that was designed by a group of people who are no longer around and I'm having difficulty getting into the box. The board has an ethernet port and two serial ports, but it doesn't look like there is a getty service running on either serial port which leaves... (0 Replies)
Discussion started by: cmcmanus3
0 Replies
6. IP Networking
Dear Experts,
I have a TI DM8148 EVM board REV C, the EZSDK5.05 SW package, and DVRRDK1.09 SW package.
EZSDK5.05, DVRRDK1.09 both use Linux2.6.37, however, there are some modifications between these two kernels.
When I use uImage of DVRRDK1.09 to boot up EVM board, this board can be given a... (0 Replies)
Discussion started by: oobin168
0 Replies
7. IP Networking
Hi All ,
please view the set up below:
-------------------------------------------------------------------
| DHCP Server |-----------| ROUTER & |-----------| Clients |
| 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X |
... (2 Replies)
Discussion started by: gdangoor
2 Replies
8. UNIX for Dummies Questions & Answers
Does anyone no why "xhost +" would not be working in freebsd? Could it be to do with a certain xorg package not being installed etc..
I am getting error "xhost: command not found"
Thanks Anyone (2 Replies)
Discussion started by: Browser
2 Replies
9. BSD
I just got FreeBSD up and running with an XFCE desktop on an old Gateway laptop. It works great, except the wireless setup is scaring me. I can connect to my home WiFi fine most of the time, but I'm concerned about other WiFi that I will need to connect to away from home.
I understand that I can... (1 Reply)
Discussion started by: BrentBANKS
1 Replies
10. IP Networking
I have a DHCP thing on my HP printer. How can I find information on numbers for that? (2 Replies)
Discussion started by: teak
2 Replies
LEARN ABOUT NETBSD
eshconfig
ESHCONFIG(8) BSD System Manager's Manual ESHCONFIG(8)
NAME
eshconfig -- configure Essential Communications' HIPPI network interface
SYNOPSIS
eshconfig [-estx] [-b bytes] [-c bytes] [-d filename] [-i usecs] [-m bytes] [-r bytes] [-u filename] [-w bytes] [interface]
DESCRIPTION
eshconfig is used to configure device-specific parameters and download new firmware to the Essential Communications RoadRunner-based HIPPI
network interface. The interface is very sensitive to the DMA performance characteristics of the host, and so requires careful tuning to
achieve reasonable performance. In addition, firmware is likely to change frequently, which necessitates a reasonably easy way to update
that firmware.
Available operands for eshconfig:
-b bytes
Adjust the burst size for read (by NIC of host memory) DMA.
-c bytes
Adjust the burst size for write (by NIC of host memory) DMA.
-d filename
Filename for file to download into NIC firmware. This must be a file in the standard Essential format, with :04 preceding every
line, and a tag line at the end indicating the characteristics of the firmware file.
-e Write data to EEPROM. Normally, setting tuning parameters will only persist until the system is rebooted. Setting this parameter
ensures that the changes will be written to EEPROM.
-i usecs
Interrupt delay in microseconds.
-m bytes
Minimum number of bytes to DMA in one direction (read or write) before allowing a DMA in the other direction. Tuning this prevents
one direction from dominating the flow of bytes, and artificially throttling the NIC.
-r bytes
Bytes before DMA starts for read (from host to NIC). This controls how soon the DMA is triggered; until this many bytes are
requested, the DMA will not begin.
-s Show statistics for the HIPPI NIC. Repeat the option to suppress non-zero statistics.
-t Show current tuning parameters on the host.
-u filename
Name of file to which the NIC firmware should be uploaded. Not currently supported.
-w bytes
Number of bytes required before write (from NIC to host) DMA is started. Until this many bytes are ready to be written, the DMA will
not start.
-x Reset the NIC. This is necessary for the HIPPI-FP support, as ifconfig(8) will no longer physically reset the NIC when the inter-
faces goes up and down.
Only the super-user may modify the configuration of a network interface.
DIAGNOSTICS
Messages indicating the specified interface does not exist or the user is not privileged and tried to alter an interface's configuration.
SEE ALSO
esh(4), ifconfig(8)
HISTORY
The eshconfig command first appeared in NetBSD 1.4.
BSD
June 17, 2005 BSD