Sponsored Content
Top Forums UNIX for Dummies Questions & Answers How to reach to the end of the file? Post 59031 by videsh77 on Wednesday 8th of December 2004 06:19:06 AM
Old 12-08-2004
MySQL

It helps, thanks buddy.

I was doing it in wrong way, not using command mode.
 

9 More Discussions You Might Find Interesting

1. BSD

How to reach files from tape drive using dd

Hi all! I have problem with copying files from tape drive. The contents of tape: silverman# tcopy /dev/sa1 file 0: block size 10240: 21 records file 0: eof after 21 records: 215040 bytes file 1: block size 10240: 20712 records file 1: eof after 20712 records: 212090880 bytes file 2:... (2 Replies)
Discussion started by: d3m00n
2 Replies

2. Solaris

Cannot access Sun 10 using Hostname and sun10 cant reach other hostnames

Hi all, I'm setting up a VM on our ESX server using Sun 10 x86. I've configured the hostname in Sun 10, but no other machine is able to use the hostname to communicate with it (i can however use its IP address) hostname is set in the /etc/nodename file my resolv.conf looks like ... (5 Replies)
Discussion started by: isellapples
5 Replies

3. Shell Programming and Scripting

Add end of char \n on end of file

Hi, I want to add \n as a EOF at the end of file if it does't exist in a single command. How to do this? when I use command echo "1\n" > a.txt and od -c a.txt 0000000 1 \n \n 0000003 How does it differentiate \n and eof in this case? Regards, Venkat (1 Reply)
Discussion started by: svenkatareddy
1 Replies

4. IP Networking

can't reach host with ipv6

Hi all, First I know little about ipv6. I have two target. A and B,A and B connet with each other *directly* with line.and I can ping each other with ipv4 For A: # ifconfig eth0 Link encap:Ethernet HWaddr 00:21:9B:80:51:68 inet addr:128.224.159.188 Bcast:128.224.159.255... (1 Reply)
Discussion started by: yanglei_fage
1 Replies

5. Infrastructure Monitoring

How to setup Email notification when storage reach certain % ?

Hi, I recently research on how auto-mailing to notify the increase of storage size. I try avoid schedule/routine checkup the storage to determine increase the storage size. It is time-consuming. Any comment on how to get the storage size %? and automatically trigger mailing function instead... (16 Replies)
Discussion started by: i-counsellor
16 Replies

6. Shell Programming and Scripting

NDM process say success but file didn't reach destination

I am using ndmcli to NDM my files. When i do so it prints success for the process, with out any errors, but file is not reached at destination. ndmcli -x << EOJ submit phcdb process snode=$RMT_NODE_NAME step01 copy from (file=$SRC_FILE_NAME pnode) to (file=$DST_FILE_NAME snode... (0 Replies)
Discussion started by: pattamuthu
0 Replies

7. Shell Programming and Scripting

Help with script to reach remote servers

new3=`cat /tmp/list3` for pol in "$new3" $(su - dbadmin -c "ssh $new3 '/usr//llist'"); do export policy=`echo $pol`; su - dbadmin -c "ssh $x '/usr/policycmd $policy -L |grep -i active; echo $policy'">>/tmp/listxyz;done I am having trouble with this testscript as the file list3 has two names... (1 Reply)
Discussion started by: newbie2010
1 Replies

8. Red Hat

PC cannot reach two lan card Linux box

we have red hat 6 linux box There are two lan card one lan card eth0 have ip 10.82.190.31/24 GW 10.82.190.254 2th lan card eth1 have ip 10.82.188.33/24 GW 10.82.188.254 I have below route ... I use two route table root@xxx# netstat -rn Kernel IP routing table Destination Gateway ... (5 Replies)
Discussion started by: chuikingman
5 Replies

9. Post Here to Contact Site Administrators and Moderators

Trying to reach Neo, but unable to.

Hello, I am trying to reach forum administrator Neo because of specific material that he posted here. I cannot reach him directly via PM him unless I have made 10 posts, but at the same time I don't want to spam the forum with 10 posts just to be able to PM him. I assume I won't be able to... (3 Replies)
Discussion started by: Artashes
3 Replies
MINBIF(8)						      System Manager's Manual							 MINBIF(8)

NAME
minbif - The IRC instant messaging gateway SYNOPSIS
minbif [-hv] [--pidfile pidfile] CONFIG_FILE DESCRIPTION
Minbif is an IRC gateway to IM networks which provides the following features: * Minbif uses a library which abstracts all IM calls, and has several plugins to support more than 15 IM protocols (IRC included!); * Two modes: inetd and daemon fork; * Only IRC commands are used to control Minbif; * IM Certificates check; * Buddies are IRC users; * Each account is associated to a status channel, where all connected buddies are; * Add and remove buddies from list with /INVITE and /KICK commands; * Blocked users are bans on the account's status channel; * Display when a buddy is typing a message; * Can chat with someone who is not in your buddy list; * You can see buddies' icons (with libcaca) or download them; * DCC SEND an image to set your icon on IM networks; * Display extended information about buddies with /WII command; * Status management; * Can send and receive files, which are sent or received to/from your IRC client with DCC SEND; * Conversation channels are supported; * Auto-rejoin conversation channels at connection; * Display list of channels on an IM account with /LIST; * irssi scripts to increase your user experience of minbif; * CACAcam (webcam in ascii art); * CoinCoin plugin for libpurple; * PAM support; * TLS support with certificate auth. OPTIONS
--pidfile pidfile path to pidfile where the minbif's PID is written. --version display version of minbif. --help show help. config_file Configuration file location. CONFIGURATION
Edit the minbif.conf file and change value when needed. With the inetd mode, use this command to add minbif: # update-inetd --add '56667 stream tcp nowait minbif /usr/sbin/tcpd /usr/bin/minbif /etc/minbif/minbif.conf' With the daemon fork mode, run minbif with: # minbif /etc/minbif/minbif.conf HOW TO USE
Connect your IRC client (for examble irssi) on minbif with this command: /server localhost 56667 password The nickname set on your IRC client is your username on minbif. First time you connect to minbif with this nickname, the account is created and the password parameter is set. Next, use the /map help command to know how to add a network. See also: http://minbif.im/Quick_start COPYRIGHT
Copyright(C) 2009-2011 Romain Bignon For full COPYRIGHT see COPYING file with minbif package. FILES
"minbif.conf" 04 December 2011 MINBIF(8)
All times are GMT -4. The time now is 03:36 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy