08-24-2001
Hardware/NIC
HI
I'm going to install Redhat 7.1 om my Compaq presario 1200 (laptop) and dual boot with Win2K. Now i have learned that my 3com fem556b-global pc-card not is supported (read on 3com's site).
My question is now can i get my card to work under Linux or even better is there a pc-card that is supported both by Linux and Win2K? And not to expencive. Is there any HCL for Linux/UNIX?
Thank for any help.
//Andreas Rönnelin
9 More Discussions You Might Find Interesting
1. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
2. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
3. Solaris
can anyone help me fix this? what command should I use to bring them back to "TRUE"?
Interface Speed Duplex Autoneg
--------- ----- ------ -------
ce0 100 Mbit/s FULL FALSE
ce5 100 Mbit/s FULL ... (3 Replies)
Discussion started by: uuontario
3 Replies
4. AIX
Hi admins
i want to assign new ip adress to my aix 5.3 machine which is in LPAR
ent3 Available Virtual I/O Ethernet Adapter (l-lan)
ent0 Available 05-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent1 Available 05-09 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent2... (0 Replies)
Discussion started by: newaix
0 Replies
5. Solaris
Hi folk,
I have this hardware faunty message, but dont know which hardware is this ? can you guide me ?
--------------- ------------------------------------ -------------- ---------
TIME EVENT-ID MSG-ID SEVERITY
---------------... (9 Replies)
Discussion started by: dehetoxic
9 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT CENTOS
opensc-tool
OPENSC-TOOL(1) OpenSC Tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--atr, -a
Print the Answer To Reset (ATR) of the card. Output is in hex byte format
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--info, -i
Print information about OpenSC, such as version and enabled components.
--list-drivers, -D
List all installed card drivers.
--list-files, -f
Recursively list all files stored on card.
--list-readers, -l
List all configured readers.
--name, -n
Print the name of the inserted card (driver).
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....
--serial
Print the card serial number (normally the ICCSN). Output is in hex byte format
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
--wait, -w
Wait for a card to be inserted.
SEE ALSO
opensc-explorer(1)
opensc 06/17/2014 OPENSC-TOOL(1)