Network card and internet Post: 58238

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

2. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.

3. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But...

4. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

5. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byte��link up...

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks

8. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

9. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101...

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4...

LEARN ABOUT DEBIAN

popbugs

popbugs(1)							  debian-goodies							popbugs(1)

NAME

       popbugs - find RC bugs in packages you commonly use

SYNOPSIS

       popbugs [options] [popularity-contest log]

DESCRIPTION

       The  popbugs  program fetches the list of release critical bugs from the Debian bug tracking system on the internet.  It correlates the bug
       log with the popularity-contest data from your system to obtain a list of release critical bugs in packages, which  are	commonly  used	on
       your  system.   Normally  this  list  is displayed in a web browser.  Helping to resolve these bugs is a good idea, if you want to see your
       favourite programs in the next stable release of Debian.

OPTIONS

       -h

       --help Show a very short usage message.

       -ooutputfile

       --output=outputfile
	      Place the output in outputfile instead of displaying it in a browser.

       -d

       --debug
	      Output debugging information.

SEE ALSO

       rc-alert(1), popularity-contest(8)

AUTHOR

       The popbugs program is copyright (C)  2001  Matt  Zimmerman  <mdz@debian.org>.	This  manual  page  is	copyright  (C)	2004   Jochen  VoB
       <voss@debian.org>.

debian-goodies							  January 10 2004							popbugs(1)

10 More Discussions You Might Find Interesting

1. IP Networking

network card

Discussion started by: cparks

2. UNIX for Dummies Questions & Answers

Installing network card

Discussion started by: gops

3. IP Networking

Network Card with SGI

Discussion started by: DPAI

4. UNIX for Advanced & Expert Users

Network Card Help

Discussion started by: The Fridgerator