11-16-2004
It might also be a good idea to find out if kudzu is functioning properly on your system...
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT DEBIAN
randomsound
RANDOMSOUND(8) System Manager's Manual RANDOMSOUND(8)
NAME
randomsound - ALSA sound card related entropy gathering daemon.
SYNOPSIS
randomsound [options]
DESCRIPTION
Using the low order bit of the ADC output of your sound card, randomsound gathers entropy, debiases it and offers it up to your kernel's
random pool. It can be tweaked to only write into the pool when it drops below a certain level, and to back off once the pool is full
enough. This build will set your sound card into 16 bit mono unsigned input at 8KHz. If your sound card cannot do that then you will need
to change the defines in asoundrunner.c and recompile the package. You must have set up asound as root on your machine. This can be done
with the asoundconf tool and its set-default-card command.
You may also need to use the alsamixer to ensure that the sound card is generating plenty of noise. Set all the gains nice and high, turn
on any boosters you have. If you have a V_REFLVL or similar then consider tweaking that.
OPTIONS
-D Daemonize
-v Increase verbosity. Can be used more than once.
-m specify minimum number of bits of entropy in the pool.
-M specify max number of bits in the pool.
-b specify number of bytes of randomness to buffer for use.
-d specify number of bytes to deposit into the pool each time.
-h display help message
-V display version information.
AUTHOR
randomsound was written by Daniel Silverstone <dsilvers@digital-scurf.org>
Pepperfish August 18, 2007 RANDOMSOUND(8)