08-23-2001
May be try set UID bit for your script and change owner for it to needed user?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
is it possible for me to have a shell script log me in to a telnet session? i have in mind something along the lines of
% telnet host < script, where the first two lines of script will be username and pass followed by a list of commands to execute on the remote host.
this doesn t work as... (4 Replies)
Discussion started by: lethe
4 Replies
2. Shell Programming and Scripting
Hello all,
I would like to login from one unix-system with a (tcsh)-script to an other unix-system.The login-procedure and the transmission of username, resp. password runs via ssh.
The problem is after logging onto the remote server once "Enter" has to be pressed, before one gets to the... (1 Reply)
Discussion started by: Juergen Paepke
1 Replies
3. Shell Programming and Scripting
Hi,
I am writing a script that will require me to perform tasks across servers. I tried to use rsh <host> "Commands..." > /dev/null 2>&1. However, I am required to execute a long series of commands after that and rsh does not seem to support this and its also insecure.
I tried to use rsh to... (5 Replies)
Discussion started by: joseph_ng
5 Replies
4. Shell Programming and Scripting
Hi,
I have a script that runs for an hour.
Have to run it on remote server and need the output it produces on the remote server to decide for failure or success.
I run it through a Autosys Job which logs the outputs, both 1 & 2.
I use the commands
1) rsh <SERVER> 'nohup /tmp/xyz.ksh &'
2)... (5 Replies)
Discussion started by: aster007
5 Replies
5. Shell Programming and Scripting
HI,
I need to write a script ..
when I run this script , will directly goto that remote machine without asking password..
Once it is entered, I needs to transfer some of the log files...
how can I proceed ? (7 Replies)
Discussion started by: hegdeshashi
7 Replies
6. Solaris
how to login with ssh to remote system with out applying the remote root/user password
with rlogin we can ujse .rhosts file
but with ssh howits possible
plz guide (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies
7. Shell Programming and Scripting
Greetings, guys. I'm not much of a programmer forgive me for being a noob, because of someone leaving, I was put in an IT spot where I have to figure out a few things. Being new to Linux and programming has been a challenge.
My boss has asked me to create an automated script to connect to a 3rd... (7 Replies)
Discussion started by: giovannym
7 Replies
8. Shell Programming and Scripting
Hi all,
I am baffled on this. Solaris Irix system.:confused:
I have 4 servers all connected to one another, :b: I need to write a script line that would login on to server 1-3 ($HOST) start a script in the back ground and log off while the back ground script runs over a length of time.:eek:
... (10 Replies)
Discussion started by: weddy
10 Replies
9. Shell Programming and Scripting
#!/bin/bash
for servers in `cat ~/servers`
do
rosh -l root -n $servers 'if
then
echo $HOSTNAME
else
exit 1
fi'
done
I have few servers in the for loop that is powered off, so whenever I execute my script, it works fine if all the servers are on, but when it tries to execute the script... (1 Reply)
Discussion started by: Rojan Shakya
1 Replies
10. Shell Programming and Scripting
Hi there,
I'm trying to run a script remotely on a server in a particular directory named after hostname which already exists, my login session gets killed as soon as I run the below command. Not sure what is wrong, is there a better way to do it ?
Note: I can also use nohup command to run... (14 Replies)
Discussion started by: mbak
14 Replies
RSH(1) General Commands Manual RSH(1)
NAME
rsh - remote shell
SYNOPSIS
rsh [-n] [-l username] host [command]
host [-n] [-l username] [command]
DESCRIPTION
Rsh connects to the specified host, and executes the specified command. Rsh copies its standard input to the remote command, the standard
output of the remote command to its standard output, and the standard error of the remote command to its standard error. Interrupt, quit
and terminate signals are propagated to the remote command; rsh normally terminates when the remote command does.
The remote username used is the same as your local username, unless you specify a different remote name with the -l option. This remote
name must be equivalent (in the sense of rlogin(1)) to the originating account; no provision is made for specifying a password with a com-
mand.
If you omit command, then instead of executing a single command, you will be logged in on the remote host using rlogin(1).
Shell metacharacters which are not quoted are interpreted on local machine, while quoted metacharacters are interpreted on the remote
machine. Thus the command
rsh otherhost cat remotefile >> localfile
appends the remote file remotefile to the localfile localfile, while
rsh otherhost cat remotefile ">>" otherremotefile
appends remotefile to otherremotefile.
OPTIONS
-l username
Specify the remote user name.
-n Connect standard input of the remote command to /dev/null. Do this if rsh should not inadvertently read from standard input.
SEE ALSO
rcp(1), rlogin(1), rhosts(5).
BUGS
You cannot run an interactive command (like rogue(6) or vi(1)); use rlogin(1).
4.2 Berkeley Distribution April 29, 1985 RSH(1)