11-04-2004
rs232 pci-card
hello mates,
do you know a manufactor for rs232 serial pci cards for the sparc architecture? it seems that there is no original product from sun for that purpose. strange, isn't it?
problem is that i have a V250 with only one db9 rs232 serial port, and i need it for a modem connection, but i also want to connect an UPS to that system. on my cognition there is no possibility to split a DB9 bus like on DB25 cables, or do i need repetition ;-)
thx in advance
greetings PRESSY
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi !
Is there somebody who is able to connect a VNC session via serial cable ?
There is a hint on the VNC homepage that it is possible to configure that.
But how?
thanks joerg (2 Replies)
Discussion started by: joerg
2 Replies
2. SuSE
Hey all, ive got redhat 80 and trying to install a HCF win modem. Ive intsalled the drivers from linuxant.com using the rpm - i packagename.rpm command, but i still cant use the modem
any suggestions ? (3 Replies)
Discussion started by: kiwi_bloke
3 Replies
3. Solaris
Hi,
i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card .
Thank You,
Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. UNIX for Dummies Questions & Answers
I have a US Robotics USR5416 wireless networking card and everytime after hours of inactivity the cardseems to shutdown. I read somewhere the it does not support power management. Is there a way to disable power management to that particular PCI card? (0 Replies)
Discussion started by: diesel440
0 Replies
6. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
7. Solaris
Hello all,
I have a problem with my x4270_m2 server. I have a GBE lan built into the back of my server and I have a QGE pci card in slot 2 to be used as a redundant.
My server is not picking up the QGE lan card in slot2. From investigation of the /etc/path_to_inst, which shows:
#grep e1000... (2 Replies)
Discussion started by: kerrygold
2 Replies
8. Solaris
Hi,
I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10).
I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies
9. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
10. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
LEARN ABOUT DEBIAN
sredird
sredird(8) sredird sredird(8)
NAME
sredird - RFC 2217 serial port server
SYNOPSIS
sredird [-i] log-level serial-device lock-file [poll-interval]
DESCRIPTION
This manual page documents briefly the sredird, program.
This program when run through inetd will use the RFC 2217 extensions to TELNET to implement serial commands over the TCP connection and
interface to a specified serial port.
OPTIONS
An optional first parameter is '-i' to enable compatability with Cisco IOS.
The first mandatory parameter is the log level for use in syslog. The next mandatory parameter is the device node for the serial device,
it must be a fully qualified path. The final mandatory parameter is the file name for the lock file to be used to prevent multiple
instances of sredird from talking to the serial port at the same time, or to allow sharing a port between modem and sredird.
EXAMPLE
Here is a configuration line for running it from inetd: sredir stream tcp nowait root /usr/sbin/tcpd /usr/sbin/sredird 5
/dev/modem /var/lock/LCK..modem
AUTHOR
This man page was written by Russell Coker <russell@coker.com.au>. May be freely used and distributed without restriction under the terms
of the GPL.
The sredird program was written by Denis Sbragion <d.sbragion@infotecna.it> and Jeffrey Altman <jaltman@columbia.edu>.
Russell Coker <russell@coker.com.au> 2.2.0 sredird(8)