rs232 pci-card Post: 57672

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

VNC via Rs232

Hi ! Is there somebody who is able to connect a VNC session via serial cable ? There is a hint on the VNC homepage that it is possible to configure that. But how? thanks joerg

2. SuSE

Hey all, ive got redhat 80 and trying to install a HCF win modem. Ive intsalled the drivers from linuxant.com using the rpm - i packagename.rpm command, but i still cant use the modem any suggestions ?

3. Solaris

Does x86 solaris 9 support PCI RealTek Lan Card

Hi, i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card . Thank You, Shafi

4. AIX

Add PCI ethernet card?

Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure...

5. UNIX for Dummies Questions & Answers

disable power management to a PCI card

I have a US Robotics USR5416 wireless networking card and everytime after hours of inactivity the cardseems to shutdown. I read somewhere the it does not support power management. Is there a way to disable power management to that particular PCI card?

6. Linux

PCI Card recognized

I installed PCI Card HP SC44Ge - SAS1068E on my linux CentOS 5.4 is there a way to find out if the PCI is properly installed and recognized by linux. lspci is enough? just to add that PCI card is connected to a tape... also how can I find out driver and firmware version? thanks a...

7. Solaris

Q:x4270_m2 reconfigure PCI card to slot 5?

Hello all, I have a problem with my x4270_m2 server. I have a GBE lan built into the back of my server and I have a QGE pci card in slot 2 to be used as a redundant. My server is not picking up the QGE lan card in slot2. From investigation of the /etc/path_to_inst, which shows: #grep e1000...

8. Solaris

Can't ping new PCI LAN card x4270_m2

Hi, I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10). I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip...

9. AIX

AIX -How to find which NIC is on which PCI card

Hi All, How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v Any idea? Thanks.

10. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI...

LEARN ABOUT DEBIAN

ne2k-pci-diag

NE2K-PCI-DIAG(8)					      System Manager's Manual						  NE2K-PCI-DIAG(8)

NAME

       ne2k-pci-diag - EEPROM setup and diagnostic program for PCI NE2000 ethernet cards.

SYNOPSIS

       ne2k-pci-diag [options]

DESCRIPTION

       ne2k-pci-diag  is  a  program  that  you  can  use  to  diagnose problems with PCI NE200 Enternet adapters. This include cards with RealTek
       RTL8029AS, Holtak HT80232 ECON-PCI, Winbond W89c940f and VIA VT86C926 (Amazon) chips.

OPTIONS

       These programs follow the usual GNU command line syntax, with long options starting with  two  dashes  (`-').   A  summary  of  options	is
       included below.

       -h, --help
	      Show summary of options.

       -V, --version
	      Show version of program.

       -v, --verbose
	      Verbose mode.

       -q, --quiet
	      Be very unverbose.

       -a, --show_all_registers
	      Print all registers.

       -# <cardnum>
	      Use card number <cardnum>.

       -e, --show-eeprom
	      Dump EEPROM contents to stdout.

       -E, --emergency-rewrite
	      Re-write a corrupted EEPROM.

       -p, --port-base <port>
	      Specify port to use.

       -F, --new-interface <interface>
	      Interface  number.  Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
	      100baseFx-FDX, MII and Autosense.

       -H, --new-hwaddress <address>
	      Set card to a new hardware address.

       -m, --show-mii
	      Dump MII management registers.

       -R, --reset
	      Reset the transceiver.

       -T, --test
	      Do register and SRAM test.

       -w, --write-EEPROM <values>
	      Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!

       -f, --force-detection
	      Try to identify the card, even if it is active.

       -t, --chip-type <card>
	      Explicitly set the chip. To get all valid numbers, run ne2k-pci-diag with the options '-t -1'.

SEE ALSO

       mii-diag(8)

AUTHOR

       ne2k-pci-diag was written and is still maintained by Donald Becker <becker@scyld.com>.  This manual page was  written  by  Alain  Schroeder
       <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).

								 February 18, 2002						  NE2K-PCI-DIAG(8)

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

VNC via Rs232

Discussion started by: joerg

2. SuSE

HCF win modem PCI card

Discussion started by: kiwi_bloke