Sponsored Content
Full Discussion: Configuring NIC
Operating Systems HP-UX Configuring NIC Post 57442 by wobitu on Thursday 28th of October 2004 05:08:18 AM
Old 10-28-2004
Error Configuring NIC

Hi.

I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card instead of using the old 10mb card ? Do I need to reinstall the Operating system ? I wish there is a shortest way of introducing the card.

I reaaly apprecaite your help in this matter.

VERY BEST REGARDS,
Wobitu.
 

8 More Discussions You Might Find Interesting

1. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies

2. Solaris

Configuring 1 Nic card with 2 IP addresses and 2 seperate default Gateways in Solaris

Hi ...... I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways. ( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip) Thanks, Remi (1 Reply)
Discussion started by: Remi
1 Replies

3. IP Networking

Problem configuring NIC in DGUX

Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten Unable to get NIC working Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

7. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

8. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ... (1 Reply)
Discussion started by: alphatron150
1 Replies
networks(4)						     Kernel Interfaces Manual						       networks(4)

NAME
networks - network name data base DESCRIPTION
The file associates Internet (IP) addresses with official network names and aliases. This allows the user to refer to a network by a sym- bolic name instead of using an Internet address. For each network, a single line should be present with the following information: <official network name> <network number> <aliases> Aliases are other names under which a network is known. For example: where the network named is also called A line cannot start with a blank (tab or space character). Items are separated by any number or combination of blanks. A character indi- cates the beginning of a comment. Characters from the up to the end of the line are not interpreted by routines which search the file. Trailing blanks are allowed at the end of a line. For the Internet, this file is normally created from the official network database main- tained at the Network Information Control Center (NIC), though local changes may be required to bring it up-to-date regarding unofficial aliases and/or unknown networks. Network numbers can be specified in conventional Internet dot notation using the routine from the internet address manipulation library (see inet(3N). Network names can contain any printable character other than a white space, new-line, or comment character. EXAMPLES
See AUTHOR
was developed by the University of California, Berkeley. FILES
SEE ALSO
getnetent(3N). networks(4)
All times are GMT -4. The time now is 02:10 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy