08-17-2001
unfortunetly i could not find that script/program anywere on the box. ;(
but good link.
i did run diag on that drive after i cleared out the error log and i didnt get any error back. ;( intermitent problems are the worst.
Last edited by Optimus_P; 08-17-2001 at 12:44 PM..
10 More Discussions You Might Find Interesting
1. AIX
Is there a simply way for me to map a vpath to an hdisk on AIX 5.2? (5 Replies)
Discussion started by: 2dumb
5 Replies
2. AIX
When I list the PV's using lspv i see both vpath and hdisk names being listed. I got the info that each vpath is configured for 4 hdisks. Problem is I am not able to add either the hard disks in vpath to the existing non-rootvg. ? need to know the basics of vpath .. (4 Replies)
Discussion started by: nivaspIND
4 Replies
3. AIX
Hi,
in an environment with svc's and ds8xxx wat disk algorithm should be used and what is the difference here:
I can set the algorithm to Load_balance and to Round_robin (see output below).
some info:
hdisk3 ******** MPIO FC 2145
devices.sddpcm.53.rte 2.2.0.0 COMMITTED ... (1 Reply)
Discussion started by: raba
1 Replies
4. AIX
How do you create a dummy hdisk with AIX 6.1? In previous versions, I've used this and works, but now I get this error.
hostname:/:# mkdev -l hdisk57 -c disk -t osdisk -s scsi -p fscsi0 -w 0,10 -d
Method error (/etc/methods/define):
0514-022 The specified connection is not valid.
Any... (2 Replies)
Discussion started by: kah00na
2 Replies
5. AIX
Hi all,
I'm getting some errors on AIX regarding Flashcopy and volume group hard disks.
The script that activates flashcopy showed this errors:
Recreating Flashcopy for lun01_A1
Performing syntax check...
Syntax check complete.
Executing script...
Script execution complete.
SMcli... (1 Reply)
Discussion started by: enux
1 Replies
6. AIX
I know the lv name (i.e. dprod_0000017).
#lslv dprod_0000017
LOGICAL VOLUME: dprod_0000017 VOLUME GROUP: prod01vg
LV IDENTIFIER: 00cb337d00004c0000000111d8566a5a.69 PERMISSION: read/write
VG STATE: active/complete LV STATE: opened/syncd
TYPE: ... (2 Replies)
Discussion started by: Daniel Gate
2 Replies
7. AIX
Hi. I found an issue with my appvg present in my server.my server is a single node and not part of hacmp.
pmut3# lspv
hdisk0 00c5c9cf92ebb96a rootvg active
hdisk1 00c5c9cfcf30eee9 appvg
hdisk2 00c5c9cfcf30ef98 ... (5 Replies)
Discussion started by: newtoaixos
5 Replies
8. Shell Programming and Scripting
Hi,
Planning to implement script to fetch whether the hdisks are in proper sequence. Need output for incorrect sequence
Correct
#lspv
hdisk0
hdisk1
hdisk2
::::::::::::
hdisk5
Incorrect sequence
#lspv
hdisk0
hdisk6
hdisk7
hdisk10
Any idea pls share (2 Replies)
Discussion started by: ksgnathan
2 Replies
9. AIX
Hello,
I have two hdisk in Power7 machine, the rootvg on hdisk0.
So to make a disk redundancy should make mirror or alt_clone and what is the different.
Appreciate your help
Thanks (1 Reply)
Discussion started by: moudmm
1 Replies
10. UNIX for Advanced & Expert Users
Hi everybody,
I have Power5 server with 4 internal hdisks each of 70Gb.
VIOS server was installed via Virtual I/O Server Image Repository on the HMC.
HMC release - 7.7.0
VIOS rootvg installed on 2 disk(these disks merged to one storage pool during VIOS install process),and 2 others hdisks... (2 Replies)
Discussion started by: Ravil Khalilov
2 Replies
LEARN ABOUT DEBIAN
myson-diag
MYSON-DIAG(8) System Manager's Manual MYSON-DIAG(8)
NAME
myson-diag - EEPROM setup and diagnostic program for ethernet cards based on the Myson MTD803 chip.
SYNOPSIS
myson-diag [options]
DESCRIPTION
myson-diag is a program that you can use to diagnose problems with ethernet cards based on the Myson MTD803 chip.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
Show summary of options.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-q, --quiet
Be very unverbose.
-# <cardnum>
Use card number <cardnum>.
-a, --show_all_registers
Print all registers.
-e, --show-eeprom
Dump EEPROM contents to stdout.
-E, --emergency-rewrite
Re-write a corrupted EEPROM.
-p, --port-base <port>
Specify port to use.
-A, --Advertise <mediaype>
Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.
-F, --new-interface <interface>
Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
100baseFx-FDX, MII and Autosense.
-H, --new-hwaddress <address>
Set card to a new hardware address.
-m, --show-mii
Dump MII management registers.
-R, --reset
Reset the transceiver.
-T, --test
Do register and SRAM test.
-w, --write-EEPROM <values>
Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!
-f, --force-detection
Try to identify the card, even if it is active.
-t, --chip-type <card>
Explicitly set the chip. To get all valid numbers, run myson-diag with the options '-t -1'.
SEE ALSO
mii-diag(8)
AUTHOR
myson-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 MYSON-DIAG(8)