09-12-2004
The linuxant driver is a trial version.
you might to pay to obtain the full version
i have one of those modems, and i've been looking for the driver..
actually i have an Intel modem because there are a lot of drivers for linux systems
9 More Discussions You Might Find Interesting
1. Solaris
hello mates,
do you know a manufactor for rs232 serial pci cards for the sparc architecture? it seems that there is no original product from sun for that purpose. strange, isn't it?
problem is that i have a V250 with only one db9 rs232 serial port, and i need it for a modem connection, but i also... (1 Reply)
Discussion started by: pressy
1 Replies
2. Solaris
Hi,
i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card .
Thank You,
Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies
3. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
4. UNIX for Dummies Questions & Answers
I have a US Robotics USR5416 wireless networking card and everytime after hours of inactivity the cardseems to shutdown. I read somewhere the it does not support power management. Is there a way to disable power management to that particular PCI card? (0 Replies)
Discussion started by: diesel440
0 Replies
5. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
6. Solaris
Hello all,
I have a problem with my x4270_m2 server. I have a GBE lan built into the back of my server and I have a QGE pci card in slot 2 to be used as a redundant.
My server is not picking up the QGE lan card in slot2. From investigation of the /etc/path_to_inst, which shows:
#grep e1000... (2 Replies)
Discussion started by: kerrygold
2 Replies
7. Solaris
Hi,
I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10).
I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies
8. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
9. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
LEARN ABOUT FREEBSD
snd_ich
SND_ICH(4) BSD Kernel Interfaces Manual SND_ICH(4)
NAME
snd_ich -- Intel ICH AC'97 and compatible bridge device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device sound
device snd_ich
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
snd_ich_load="YES"
DESCRIPTION
The snd_ich bridge driver allows the generic audio driver sound(4) to attach to Intel ICH AC'97 and compatible audio devices.
Some later chips, like ICH6/ICH7, depending on wiring can instead implement newer Intel HD Audio specification, which is supported by
snd_hda(4) driver.
HARDWARE
The snd_ich driver supports the following audio devices:
o AMD 768
o AMD 8111
o Intel 443MX
o Intel ICH
o Intel ICH revision 1
o Intel ICH2
o Intel ICH3
o Intel ICH4
o Intel ICH5
o Intel ICH6
o Intel ICH7
o NVIDIA nForce
o NVIDIA nForce2
o NVIDIA nForce2 400
o NVIDIA nForce3
o NVIDIA nForce3 250
o NVIDIA nForce4
o SiS 7012
SEE ALSO
snd_hda(4), sound(4)
HISTORY
The snd_ich device driver first appeared in FreeBSD 4.2.
AUTHORS
This manual page was written by Jorge Mario G. Mazo <jgutie11@eafit.edu.co>.
BSD
January 6, 2009 BSD