09-08-2004
does fc stands for fiber channel?
I need a detailed configuration steps which can help me in configuring both the system for the cluster.
Regards,
9 More Discussions You Might Find Interesting
1. UNIX Benchmarks
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250
Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004
1 interactive users.
Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies
2. Solaris
Hi,
I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly.
I would like to know whether it is possible and also on which... (5 Replies)
Discussion started by: RajaRC
5 Replies
3. Gentoo
We are retiring a Sun e250 at work, and I wondered if I could put it to any good use. Will I have any problems loading Linux as opposed to Solaris? Should I use any particular flavor of Linux that might be more Sun friendly? Assuming I manage to load Linux on this server, then what? Will it be... (9 Replies)
Discussion started by: kccrusher
9 Replies
4. Solaris
Hello,
Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies
5. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
6. Solaris
Hi All
I hav working knowledge on solarois 10.
Could anyone suggest me any doc or material for learning SUN cluster from scratch. Anything from basic level .
Thanks in advance!! (1 Reply)
Discussion started by: ningy
1 Replies
7. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
8. Solaris
Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem.
I have a sun solaris server e250 enterprise with sun 5 versionof O.S.
Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies
9. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
LEARN ABOUT OPENSOLARIS
scsetup
scsetup(1M) System Administration Commands scsetup(1M)
NAME
scsetup - interactive cluster configuration tool
SYNOPSIS
scsetup [-f logfile]
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
The scsetup command provides the following configuration capabilities, depending on what state the cluster is in when you issue the com-
mand:
o When you run the scsetup command at post-installation time, the command performs initial setup tasks, such as configuring quorum
devices and resetting the installmode property. If you did not use automatic quorum configuration when you created the cluster,
run the scsetup command immediately after the cluster is installed. Ensure that all nodes have joined the cluster before you run
the scsetup command and reset the installmode property.
If you used automatic quorum configuration when you created the cluster, you do not need to run the scsetup command after clus-
ter installation. The automatic quorum configuration feature also resets the installmode property of the cluster.
o When you run the command during normal cluster operation, the scsetup command provides a menu-driven utility. You can use this
utility to perform most ongoing cluster-administration tasks.
o When you issue the command from a node that is in noncluster mode, the scsetup utility provides a menu-driven utility for chang-
ing and displaying the private IP address range. You must reboot all nodes into noncluster mode before you start this form of
the scsetup utility.
You can issue the scsetup command from any node in the cluster.
You can use this command only in the global zone.
OPTIONS
The following options are supported:
-f logfile Specifies the name of a log file to which commands can be logged. If you specify this option, most command sets that
the scsetup utility generates are run and logged, or only logged, depending on user responses.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes.
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsczu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
Intro(1CL), cltelemetryattribute(1CL), cldevicegroup(1CL), clnode(1CL), clquorum(1CL), clreslogicalhostname(1CL), clresourcegroup(1CL),
clresourcetype(1CL), clressharedaddress(1CL), cluster(1CL),
Sun Cluster 3.2 18 Jul 2006 scsetup(1M)