09-01-2004
LAN card problem
Dear all
Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working.
Is there any solution
Thanks & Regards
Charu Vyas
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
The Lan card in one of our UIII WS's seem doesn't work,so with ping command i can not see any of the machines in LAN and with some other tests i'm sure it's not OK.
I tried to use the second card on PCI port ,but the replaced card was one of the ordinary card for PC's ...by the way after... (1 Reply)
Discussion started by: nikk
1 Replies
2. Cybersecurity
what is lan card autonegotiation ?
how to enable and disable this feature? (2 Replies)
Discussion started by: nabil_boussetta
2 Replies
3. Solaris
Hi,
i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card .
Thank You,
Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies
4. SCO
hi all
i have installed SCO 5.0.5 on a "Netfinity 5000" IBM server. But the OS is not detecting the lan card. how can i detect it.... help and thanks in advance .
bidhayak (3 Replies)
Discussion started by: bidhayakm
3 Replies
5. Programming
Please tell me API in Solaris / Linux / UNIX to get status information of LAN card. (1 Reply)
Discussion started by: mansoorulhaq
1 Replies
6. Linux
Hi.
I have a lan card installed on my server. I want to check the duplex speed of it. How can I check it?
Help is appreciated.
Thank you. (3 Replies)
Discussion started by: Amol21
3 Replies
7. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
8. Solaris
Hi,
I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10).
I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies
9. Linux
Hi,
I have this problem on RHEL box. I am using two NIC's of same model and make (Intel 82557) in the adjacent PCI slots . I am using each one for different subnet and have assigned them ipaddresses and gateways of respective subnets . While one is O.K. connecting to its ... (5 Replies)
Discussion started by: dextergenious
5 Replies
10. Red Hat
we have red hat 6 linux box
There are two lan card
one lan card eth0 have ip 10.82.190.31/24 GW 10.82.190.254
2th lan card eth1 have ip 10.82.188.33/24 GW 10.82.188.254
I have below route ... I use two route table
root@xxx# netstat -rn
Kernel IP routing table
Destination Gateway ... (5 Replies)
Discussion started by: chuikingman
5 Replies
lan(7) Miscellaneous Information Manual lan(7)
NAME
lan - network I/O card access information
DESCRIPTION
This manual entry gives a brief description on how to access the LAN device driver at Layer 2 (Data Link Layer) of the OSI architecture.
The LAN device driver controls the various LAN interface cards (e.g, Ethernet/IEEE 802.3, FDDI, Token Ring) at Layer 1 (Physical Layer).
The Data Link Provider Interface (DLPI) is the supported method for accessing the LAN device driver at Layer 2. DLPI is intended for use
by knowledgeable network users only. Refer to the for complete programming details.
There are HP and non-HP drivers and interface cards which will provide their own DLPI module. These types of DLPI are referred to as
"native" DLPI.
Overview
The Physical Point of Attachment (PPA) is a numerical value that uniquely identifies a particular device. The PPA value can be obtained
from the and commands. The "ClassInstance" identifier in the output is the concatenation of the driver class (lan) and the PPA number.
The "NamePPA" identifier in the output is a concatenation of the interface name and the PPA number. The value for a lan device is equiva-
lent to the PPA number for that device.
A single hardware device may have multiple "NamePPA" identifiers, which indicates multiple encapsulation methods supported for to the
device. For Ethernet/IEEE 802.3 links, the "Name" is used to designate Ethernet encapsulation, and for IEEE 802.3 encapsulation. For
other links (FDDI, Token Ring), only the encapsulation designation is used.
Methods of transfer over the DLPI interface through the lan devices include "raw", "connectionless", and "connection-oriented" data trans-
fers.
WARNINGS
The and commands are deprecated. These commands will be removed in a future HP-UX release. HP recommends the use of replacement command
nwmgr(1M) to perform all network interface-related tasks.
AUTHOR
was developed by HP.
SEE ALSO
lanscan(1M), lanadmin(1M), linkloop(1M), nwmgr(1M).
1995, Hewlett-Packard
Version 2.0, November 1982, Digital Equipment Corporation, Intel Corporation, Xerox Corporation
1996, Institute of Electrical and Electronic Engineers
1996, Institute of Electrical and Electronic Engineers
1995, ANSI
1995, Institute of Electrical and Electronic Engineers
1995, Institute of Electrical and Electronic Engineers
lan(7)