08-05-2004
Hi,
It depends on the OS you're using... it is something like /dev/cua0...
10 More Discussions You Might Find Interesting
1. Linux
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Discussion started by: noratx
2 Replies
2. Ubuntu
Hello!
I am working on an application which reads environmental instruments which have serial ports. The application requires a serial port to be present to talk to the device (i.e. /dev/ttyS0 ). In some instances the environmental devices will be 100's of yards away from the computer, so a... (5 Replies)
Discussion started by: mvona
5 Replies
3. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
4. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
5. Solaris
Any help much appreciated. I am a Java developer, not a Solaris adept. I'm having an issue reopening serial port with the Java app I am developing.
I develop in Windows and deploy the app on Solaris 10 (Sunfire X4170 with Xeon.) On the target machine my app uses the two serial ports... (11 Replies)
Discussion started by: Jim Ryan
11 Replies
6. SCO
I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
lpstat -s
device for check3: /dev/ttyr002
device for check4: /dev/ttyr002
I changed the tty setting for check3 in:
/etc/printcap
/var/spool/lp/admins/lp/printers/check3
to /dev/ttyr014
Then I get:... (4 Replies)
Discussion started by: herot
4 Replies
7. Red Hat
Hi,
I have a server program that reads data coming in on USB ports. Device paths are in the format: /dev/ttyUSB0
Now, I would like to log data from another device coming in over Ethernet. My first step is trying to track down what the correct device path is which I am unsure of.
Anyone... (9 Replies)
Discussion started by: fedora18
9 Replies
8. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
9. Shell Programming and Scripting
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
10. UNIX for Advanced & Expert Users
Currently I am using this laborious command
lvdisplay | awk '/LV Path/ {p=$3} /LV Name/ {n=$3} /VG Name/ {v=$3} /Block device/ {d=$3; sub(".*:", "/dev/dm-", d); printf "%s\t%s\t%s\n", p, "/dev/mapper/"v"-"n, d}'
Would like to know if there is any shorter method to get this mapping of... (2 Replies)
Discussion started by: royalibrahim
2 Replies
LEARN ABOUT DEBIAN
microcom
MICROCOM(1) General Commands Manual MICROCOM(1)
NAME
microcom -- A minimalistic terminal program
SYNOPSIS
microcom [-p devfile] [-s speed] [-t host:port] [-c interface:rx_id:tx_id]
DESCRIPTION
This manual page documents briefly the microcom command.
This manual page was written for the Debian distribution because the original program does not have a manual page.
microcom is a is a minimalistic terminal program for accessing devices (e.g. switches) via a serial connection. It features connection
via RS232 serial interfaces (including setting of transferrates) as well as in `telnetmode' as specified in rfc2217.
The default escape character is crtl-. You may enter the program menu with the escape character followed by c. You may leave the program
by the escape character followed by q.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below. For a complete description, see the Info files.
-h --help
Show help.
-p --port
use the specified serial port device (default /dev/ttyS0).
-s --speed
use specified baudrate (default 115200).
-t --telnet
work in telnet (rfc2217) mode.
-c --can
work in CAN mode (default: (can0:200:200))
-d --debug
turn on debug mode.
AUTHOR
This manual page was written by Alexander Reichle-Schmehl tolimar@debian.org for the Debian system (and may be used by others). Permission
is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 any later version
published by the Free Software Foundation.
On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL-2.
MICROCOM(1)