07-05-2004
.........
you just need a db9 to db25 cross cable.
put the db9 into your pc and the db25 to the e250 serial_A.
settings: 9600/8/N/1
lg P
8 More Discussions You Might Find Interesting
1. UNIX Benchmarks
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250
Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004
1 interactive users.
Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies
2. Solaris
it there any docs out there anyhwre that have the specs for cabing to a sun console.
I have an e420 here, i cant seem to get a console connection, i have triewd the silver serial connectors that come with the new dsun servers, but no luck with those. (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies
3. Gentoo
We are retiring a Sun e250 at work, and I wondered if I could put it to any good use. Will I have any problems loading Linux as opposed to Solaris? Should I use any particular flavor of Linux that might be more Sun friendly? Assuming I manage to load Linux on this server, then what? Will it be... (9 Replies)
Discussion started by: kccrusher
9 Replies
4. Solaris
Hi,
I need some help, since I am new to cluster.
I am handling a site where I have look after two SUN E250 server.
I have been asked to configure Active-Active Clustering on these servers.
I would like to know how to configure both the servers for clustering.
Below are the things which... (5 Replies)
Discussion started by: RajaRC
5 Replies
5. Solaris
Hello,
Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies
6. Solaris
Hi :
I have a e450 sun server that I just started up and I connect my laptop to the serial connection using a null modem cable and it just does not connect.
I use hyperterminal, I dont connect a keyboard to the sun machine?
Any ideas?
Thanks a lot
Al (3 Replies)
Discussion started by: alanj4
3 Replies
7. Solaris
Hi,
I have Solaris 10 8/07 on SPARC and I can't log in Web console. When I opened browser (Firefox 3) at localhost:6789 I get Save file dialog which asks me to save some file with .part at the end. What information should I provide to find out where is the trouble?..
Internet explorer says... (3 Replies)
Discussion started by: Sapfeer
3 Replies
8. Solaris
Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem.
I have a sun solaris server e250 enterprise with sun 5 versionof O.S.
Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies
LEARN ABOUT DEBIAN
rds-ping
RDS-PING(1) BSD General Commands Manual RDS-PING(1)
NAME
rds-ping -- test reachability of remote node over RDS
SYNOPSIS
rds-ping [-c count] [-i interval] [-I local_addr] remote_addr
DESCRIPTION
rds-ping is used to test whether a remote node is reachable over RDS. Its interface is designed to operate pretty much the standard ping(8)
utility, even though the way it works is pretty different.
rds-ping opens several RDS sockets and sends packets to port 0 on the indicated host. This is a special port number to which no socket is
bound; instead, the kernel processes incoming packets and responds to them.
OPTIONS
The following options are available for use on the command line:
-c count
Causes rds-ping to exit after sending (and receiving) the specified number of packets.
-I address
By default, rds-ping will pick the local source address for the RDS socket based on routing information for the destination address
(i.e. if packets to the given destination would be routed through interface ib0, then it will use the IP address of ib0 as source
address). Using the -I option, you can override this choice.
-i timeout
By default, rds-ping will wait for one second between sending packets. Use this option to specified a different interval. The timeout
value is given in seconds, and can be a floating point number. Optionally, append msec or usec to specify a timeout in milliseconds
or microseconds, respectively.
Specifying a timeout considerably smaller than the packet round-trip time will produce unexpected results.
AUTHORS
rds-ping was written by Olaf Kirch <olaf.kirch@oracle.com>.
SEE ALSO
rds(7), rds-info(1), rds-stress(1).
BSD
Apr 22, 2008 BSD