06-29-2004
I had not even heard of it till this post - looks like it's about the same as most of the rest but I doubt I could explain it well enough so go to the
admin guide - network for assistance.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
HELP!! How do you change the network setting from auto-duplex to 100 Base T Full Duplex in Red HaT? (1 Reply)
Discussion started by: johnlong
1 Replies
2. Linux
I've been looking for documentation on how to stop this behavior. I have two nics in my system.
eth0: configured manually and as a dhcp server for the local network
eth1: configured w/ dhcp enabled connected to router
dns server addresses keep getting reset every few minutes. i suspect... (0 Replies)
Discussion started by: rbetzen
0 Replies
3. Solaris
I have problem with network settings.
Where i can find network config ? I'm newbie, but i very want learn this OS.
I find :
/etc/hostname.<interface>
/etc/netconfig
/etc/netmasks
/etc/networks
/etc/inet/hosts
But where i can write my IP-address and after reboot i be know that my server... (2 Replies)
Discussion started by: jess_t03
2 Replies
4. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
5. HP-UX
Hello everyone..
While printing through command line, we can set printing option with -o <lanscape/portrait> to print file in required mode.
But i want to know is there any way we can set this as default behaviour for this printer?
After configuration any script we can modify for this... (0 Replies)
Discussion started by: laxmikant
0 Replies
6. UNIX for Dummies Questions & Answers
Hello Unix Gurus Who I Hope Reads This,
I have quasi-inherited control over a Linux cluster at a university research lab. The post-doc that set it up is gone, and the person in charge of administering the cluster doesn't know a ton about Linux. Amongst other things, I want to use the cluster... (0 Replies)
Discussion started by: mbl
0 Replies
7. Solaris
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies
8. Shell Programming and Scripting
Hello, Newbie question on scripting - I'm looking to create a simple script that will work on RHEL5 that will adjust the network settings: ip address, default gateway, and subnet mask. If anything else needs to be done (service network stop / start) or should be done to make settings active - I... (4 Replies)
Discussion started by: rojizo
4 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I have inherited a Motorola System V R32V3.2 system. The system works fine, but we need to change the network settings. I've changed the IP address successfully, however I'm lost on the gateway and subnet mask. I've changed the default gateway using route -g10.0.8.1, but it changes back to... (7 Replies)
Discussion started by: Tilmar
7 Replies
LEARN ABOUT CENTOS
reporter-upload
REPORTER-UPLOAD(1) LIBREPORT MANUAL REPORTER-UPLOAD(1)
NAME
reporter-upload - Uploads compressed tarball of problem directory.
SYNOPSIS
reporter-upload [-c CONFFILE]... [-d DIR] [-u URL]
DESCRIPTION
The tool is used to create a compressed tarball of the problem directory and upload it to a URL. Supported protocols include FTP, FTPS,
HTTP, HTTPS, SCP, SFTP, TFTP and FILE.
Configuration file
Configuration file contains entries in a format "Option = Value".
The options are:
URL
The URL where tarball should be uploaded.
Integration with ABRT events
reporter-upload can be used as a reporter, to allow users to upload compressed tarballs of problem directories to a configured URL. This
usage can be configured in /etc/libreport/report_event.conf:
EVENT=report_Upload reporter-upload
It can be also used on the post-create event to upload it automatically.
EVENT=post-create reporter-upload
OPTIONS
-d DIR
Path to problem directory.
-c CONFFILE
Path to configuration file. When used in ABRT event system, the file contains site-wide configuration. Users can change the values via
environment variables.
-u URL
The URL where tarball should be uploaded. URL should have form protocol://[user[:pass]@]host/dir/[file.tar.gz] where protocol can be
http(s), ftp, scp, or file. File protocol can't have user and host parts: file.tar.gz[1]. If URL ends with a slash, the archive name
will be generated and appended to URL; otherwise, URL will be used as full file name.
ENVIRONMENT VARIABLES
Environment variables take precedence over values provided in the configuration file.
Upload_URL
The URL where should be the tarball uploaded.
AUTHORS
o ABRT team
NOTES
1. file.tar.gz
file:///dir/
LIBREPORT 2.1.11 06/18/2014 REPORTER-UPLOAD(1)