06-12-2004
Thanks for the link. It's good to see another site supporting such a fine OS.
Dave
6 More Discussions You Might Find Interesting
1. IP Networking
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
2. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
3. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
4. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
5. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
6. What is on Your Mind?
Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not... (13 Replies)
Discussion started by: Circuits
13 Replies
LEARN ABOUT OPENSOLARIS
ng_split
NG_SPLIT(4) BSD Kernel Interfaces Manual NG_SPLIT(4)
NAME
ng_split -- netgraph node to separate incoming and outgoing flows
SYNOPSIS
#include <netgraph/ng_split.h>
DESCRIPTION
The split node type is used to split a bidirectional stream of packets into two separate unidirectional streams of packets.
HOOKS
This node type supports the following three hooks:
in Packets received on in are forwarded to mixed.
out Packets received on out will be discarded as illegal.
mixed Packets received on mixed are forwarded to out.
CONTROL MESSAGES
This node type supports only the generic control messages.
SHUTDOWN
This node shuts down upon receipt of a NGM_SHUTDOWN control message, or when all hooks have been disconnected.
SEE ALSO
netgraph(4), ngctl(8)
HISTORY
The ng_split node type was implemented in FreeBSD 3.5 but incorporated into FreeBSD in FreeBSD 5.0.
AUTHORS
Julian Elischer <julian@FreeBSD.org>
Vitaly V. Belekhov <vitaly@riss-telecom.ru>
BSD February 19, 2001 BSD