06-08-2004
Do you get any problems if you try ifconfig again on reboot..
May be you need to set this in /etc/hostname.hme0:1
9 More Discussions You Might Find Interesting
1. IP Networking
I have a SCO OpenServer 5.0.5 and my cuestion is can i have 2 ip address in one nic?, how?.
Thanks. (1 Reply)
Discussion started by: dvl
1 Replies
2. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
3. Shell Programming and Scripting
how can I know the Network Interface Card physical address? (4 Replies)
Discussion started by: nokia1100
4 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. IP Networking
hi all,
i have an udp based application that doesn't bind to any particular address.
-->while sneding the packets, i have some doubts....
1) can the packet be transmitted with an source ip address as 0.0.0.0
2) if we select an interface based on destination ip address,... (0 Replies)
Discussion started by: vijaypdp2006
0 Replies
6. UNIX for Dummies Questions & Answers
Hi guys,
I got one problem which I definetily no idea.
What would the physical address be for virtual address?
1) 2ABC
2) 3F4B
Here is the page table:see attached
Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies
7. Solaris
Hi everybody!
I'm facing a problem and I doubt about the solution (I'm not very familiar with old *NIXs).
An external network supplier (let's call them "telco") just installed new communication components that filters MAC addresses.
I have a Solaris 5 server, with 1 NIC (hte0) which is... (6 Replies)
Discussion started by: Isharfoxat
6 Replies
8. Solaris
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies
9. Red Hat
am try to create another network card as virtual eth0:1
but when i restart the server it want be appear i have to create it again what is the solution for this . (6 Replies)
Discussion started by: leganti
6 Replies
HALT(8) halt HALT(8)
NAME
halt, poweroff, reboot - Halt, power-off or reboot the machine
SYNOPSIS
halt [OPTIONS...]
poweroff [OPTIONS...]
reboot [OPTIONS...]
DESCRIPTION
halt, poweroff, reboot may be used to halt, power-off or reboot the machine.
OPTIONS
The following options are understood:
--help
Prints a short help text and exits.
--halt
Halt the machine, regardless of which one of the three commands is invoked.
-p, --poweroff
Power-off the machine, regardless of which one of the three commands is invoked.
--reboot
Reboot the machine, regardless of which one of the three commands is invoked.
-f, --force
Force immediate halt, power-off, reboot. Do not contact the init system.
-w, --wtmp-only
Only write wtmp shutdown entry, do not actually halt, power-off, reboot.
-d, --no-wtmp
Do not write wtmp shutdown entry.
--no-wall
Do not send wall message before halt, power-off, reboot.
EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise.
NOTES
These are legacy commands available for compatibility only.
SEE ALSO
systemd(1), systemctl(1), shutdown(8), wall(1)
systemd 208 HALT(8)