06-07-2004
Binding Virtual IP address to NIC
Hi,
I bound a virtual IP to a network card on my E450 server and I am getting this error when I reboot the server, saying, " retrying host, RPC time out. I had to break this sequence and allow other services to load. Of course they didn't load properly. Please how can I sort this out? I do need to bind this IP address to this NIC. Thanks.
9 More Discussions You Might Find Interesting
1. IP Networking
I have a SCO OpenServer 5.0.5 and my cuestion is can i have 2 ip address in one nic?, how?.
Thanks. (1 Reply)
Discussion started by: dvl
1 Replies
2. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
3. Shell Programming and Scripting
how can I know the Network Interface Card physical address? (4 Replies)
Discussion started by: nokia1100
4 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. IP Networking
hi all,
i have an udp based application that doesn't bind to any particular address.
-->while sneding the packets, i have some doubts....
1) can the packet be transmitted with an source ip address as 0.0.0.0
2) if we select an interface based on destination ip address,... (0 Replies)
Discussion started by: vijaypdp2006
0 Replies
6. UNIX for Dummies Questions & Answers
Hi guys,
I got one problem which I definetily no idea.
What would the physical address be for virtual address?
1) 2ABC
2) 3F4B
Here is the page table:see attached
Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies
7. Solaris
Hi everybody!
I'm facing a problem and I doubt about the solution (I'm not very familiar with old *NIXs).
An external network supplier (let's call them "telco") just installed new communication components that filters MAC addresses.
I have a Solaris 5 server, with 1 NIC (hte0) which is... (6 Replies)
Discussion started by: Isharfoxat
6 Replies
8. Solaris
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies
9. Red Hat
am try to create another network card as virtual eth0:1
but when i restart the server it want be appear i have to create it again what is the solution for this . (6 Replies)
Discussion started by: leganti
6 Replies
ypset(1M) System Administration Commands ypset(1M)
NAME
ypset - point ypbind at a particular server
SYNOPSIS
/usr/sbin/ypset [-d ypdomain] [-h host] server
DESCRIPTION
In order to run ypset, ypbind must be initiated with the -ypset or -ypsetme options. See ypbind(1M). ypset tells ypbind to get NIS services
for the specified ypdomain from the ypserv process running on server. If server is down, or is not running ypserv, this might not be dis-
covered until an NIS client process tries to obtain a binding for the domain. At this point, the binding set by ypset is tested by ypbind.
If the binding is invalid, ypbind attempts to rebind for the same domain.
ypset is useful for binding a client node that is not on a broadcast net, or is on a broadcast net that is not running an NIS server host.
It is also useful for debugging NIS client applications, for instance, where an NIS map exists only at a single NIS server host.
Where several hosts on the local net are supplying NIS services, ypbind can rebind to another host, even while you attempt to find out if
the ypset operation succeeded. For example, if you enter the ypset command below, you might get the subsequent response from ypwhich:
example% ypset host1
example% ypwhich
host2
The sequence shown above is a function of the NIS subsystem's attempt to load-balance among the available NIS servers, and occurs when
host1 does not respond to ypbind because it is not running ypserv (or is overloaded), and host2, running ypserv, obtains the binding.
server indicates which NIS server to bind to, and must be specified as a name or an IP address. This works only if the node has a current
valid binding for the domain in question and ypbind has been set to allow use of ypset. In most cases, server should be specified as an IP
address.
ypset tries to bind over a connectionless transport. The NIS library call, yp_all(), uses connection-oriented transport and derives the
NIS server's address based on the connectionless address supplied by ypset.
Refer to ypfiles(4) for an overview of the NIS name service.
OPTIONS
-d ypdomain Use ypdomain, instead of the default domain.
-h host Set ypbind's binding on host, instead of locally. Specify host as a name.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWnisu |
+-----------------------------+-----------------------------+
SEE ALSO
ypwhich(1), ypfiles(4), attributes(5)
SunOS 5.10 14 Sep 1992 ypset(1M)