Dell Poweredge 2400 / 533 Post: 51833

Sponsored Content

UNIX Standards and Benchmarks UNIX & LINUX Benchmarks (Version 3.11) Linux Benchmarks Dell Poweredge 2400 / 533 Post 51833 by happy*nix on Wednesday 2nd of June 2004 11:31:40 PM

06-03-2004

Registered User

Gentoo 2004.1 AMD64

RIG: Nvidia Gforce3 250
AMD Athlon64 2800 (412MHz FSB)
2GB PC3200 RAM (2, 1GB DIMMS)
Hitachi 160GB SATA Drives
3ware escalade RAID controller Raid5
GENTOO 2004.1 stage2 install 64bit

CHOST="x86_64-pc-linux-gnu"
CFLAGS="-DTIME -msse -msse2 -m3dnow -m64 -O2"

Results:

Quote:

BYTE UNIX Benchmarks (Version 3.11)
System -- Linux VES-bear 2.6.5-gentoo-r1 #2 Sat May 22 21:23:30 Local time zone must be set--see zic manu x86_64 4 GNU/Linux
Start Benchmark Run: Mon May 31 21:52:23 CDT 2004
13 interactive users.
Dhrystone 2 without register variables 5398108.6 lps (10 secs, 6 samples)
Dhrystone 2 using register variables 5360057.0 lps (10 secs, 6 samples)
Arithmetic Test (type = arithoh) 8559222.0 lps (10 secs, 6 samples)
Arithmetic Test (type = register) 384388.5 lps (10 secs, 6 samples)
Arithmetic Test (type = short) 376582.4 lps (10 secs, 6 samples)
Arithmetic Test (type = int) 384470.8 lps (10 secs, 6 samples)
Arithmetic Test (type = long) 224603.1 lps (10 secs, 6 samples)
Arithmetic Test (type = float) 976770.2 lps (10 secs, 6 samples)
Arithmetic Test (type = double) 881900.2 lps (10 secs, 6 samples)
System Call Overhead Test 1833903.8 lps (10 secs, 6 samples)
Pipe Throughput Test 1192333.6 lps (10 secs, 6 samples)
Pipe-based Context Switching Test no measured results
Process Creation Test 11411.8 lps (10 secs, 6 samples)
Execl Throughput Test no measured results
File Read (10 seconds) 4920490.0 KBps (10 secs, 6 samples)
File Write (10 seconds) 613887.0 KBps (10 secs, 6 samples)
File Copy (10 seconds) 101231.0 KBps (10 secs, 6 samples)
File Read (30 seconds) 4949798.0 KBps (30 secs, 6 samples)
File Write (30 seconds) 632218.0 KBps (30 secs, 6 samples)
File Copy (30 seconds) 45708.0 KBps (30 secs, 6 samples)
C Compiler Test 1193.7 lpm (60 secs, 3 samples)
Shell scripts (1 concurrent) 5188.3 lpm (60 secs, 3 samples)
Shell scripts (2 concurrent) 2735.7 lpm (60 secs, 3 samples)
Shell scripts (4 concurrent) 1405.3 lpm (60 secs, 3 samples)
Shell scripts (8 concurrent) 709.3 lpm (60 secs, 3 samples)
Dc: sqrt(2) to 99 decimal places 160117.5 lpm (60 secs, 6 samples)
Recursion Test--Tower of Hanoi 90029.9 lps (10 secs, 6 samples)

INDEX VALUES
TEST BASELINE RESULT INDEX

Arithmetic Test (type = double) 2541.7 881900.2 347.0
Dhrystone 2 without register variables 22366.3 5398108.6 241.4
Execl Throughput Test 16.5 0.0 0.0
File Copy (30 seconds) 179.0 45708.0 255.4
Pipe-based Context Switching Test 1318.5 0.0 0.0
Shell scripts (8 concurrent) 4.0 709.3 177.3
=========
SUM of 6 items 1021.0
AVERAGE 170.2

happy*nix

View Public Profile for happy*nix

Find all posts by happy*nix

8 More Discussions You Might Find Interesting

1. Linux Benchmarks

Dell Dual Xeon PowerEdge 4600

Notes: System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz 1988.782 MHz) hyperthreaded System clock frequency: 99.0827 MHz Memory size (approximate): 2559 Megabytes ========================= CPUs ======================== CPU # CPU...

2. Solaris

Installing Solaris 10 on Dell PowerEdge 2800

hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request... the installation crashes when trying to detect the NICS...

3. Red Hat

Installing RedHat 8.0 onto Dell PowerEdge SC1425 - hdc: status error: status = 0x58

I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive. Using the following kernel parameters, i successfully installed across both hard drives from CD: ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert...

4. Filesystems, Disks and Memory

Linux and Dell 1500sc Poweredge Server

Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,...

5. UNIX for Dummies Questions & Answers

Stange problem Dell PowerEdge 1950/ Boradcom Netextreme NIC

I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ...

6. SCO

Continueing relyability problems with SCO 6.0 on Dell Poweredge 1800 with PERC DC4.

Hello all, I'am experiencing weird relyability problems with a SCO 6.0 Openserver server that runs on a Dell Poweredge 1800 equipped with a PERC DC4 raid controller and 4 36 GB 15 K rpm hot swappable scsi harddisks. It runs a RAID 10 configuration. It uses the mega hba, Revision 8.03a Release...

7. Programming

/dev/mem on Dell Poweredge

Hi, I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines. I receive a 'EFAULT' when I try to access /dev/mem on these servers. I suspect some...

8. SCO

Dell PowerEdge 2600 tape backup

I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site. The only device names in /dev for a tape drive were /dev/xStp0 /dev/xcdt0 /dev/xct0 ...

LEARN ABOUT SUNOS

raidctl

raidctl(1M)						  System Administration Commands					       raidctl(1M)

NAME

       raidctl - RAID hardware utility

SYNOPSIS

       raidctl -c disk1 disk2

       raidctl -d disk1

       raidctl [-f] -F filename controller...

       raidctl -l [controller...]

DESCRIPTION

       The  raidctl  utility  creates, deletes, or displays RAID volumes of the LSI1030 HW Raid controllers that include RAID support. The utility
       also updates firmware/fcode/BIOS for both RAID and non-RAID controllers.

       The raidctl utility requires privileges that are controlled by the underlying file-system permissions. Only privileged users can manipulate
       the RAID system configuration. If a non-privileged user attempts to create or delete a RAID volume, the command fails with EPERM.

       Without options, raidctl displays the current RAID configuration on all exisiting controllers.

OPTIONS

       The following options are supported:

       -c disk1 disk2 (for on board)

	   Create  a  mirror using disk1 and disk2. Replace the contents of disk2 with the contents of disk1. Specify disk1 and disk2 in canonical
	   form, for example, c0t0d0.

	   When you create a a RAID volume, the RAID volume assumes the identity of the first target in the disk pair (disk1). The  second  target
	   (disk2) disappears from the system. Therefore, the RAID volume appears as one disk.

	   To  have  a successful RAID creation, there must not already be a RAID configuration present on the specified controller. Additionally,
	   the secondary disk must not be mounted, as it has all its data erased and replaced with the primary disk's data.

       -d disk1 (for on board)

	   Delete the RAID volume specified as disk1.

	   Specify disk1 in canonical form, for example, c0t0d0.

       -f (for HBA)

	   Force an update. Do not prompt.

       -F filename controller (for HBA)

	   Update the firmware running on the specified controller (controller).

       -l [controller ...] (for on board)

	   List the system's RAID configuration. If controller is specified, list RAID configurations for controller.

	   Output from the -l lists the following information:

	   RAID Volume	   Displays logical RAID volume name.

	   RAID Status	   Displays RAID status as either RESYNCING (disks are syncing), DEGRADED RAID is operating with  reduced  functionality),
			   OK (operating optimally), or FAILED (non-functional).

	   RAID Disk	   Displays RAID disk name.

	   Disk Status	   Displays disk status as either OK or FAILED.

EXAMPLES

       Example 1: Creating the RAID Configuration

       The following command creates the RAID configuration:

       # raidctl -c c0t0d0 c0t1d0
       RAID Volume 'c0t0d0' created

       Example 2: Displaying the RAID Configuration

       The following command displays the RAID configuration:

       # raidctl
       RAID	 RAID	   RAID      Disk
       Volume	 Status    Disk      Status
       ----------------------------------------
       c0t0d0	 RESYNCING c0t0d0    OK
			   c0t1d0    OK

       Example 3: Deleting the RAID Configuration

       The following command deletes the RAID configuration:

       # raidctl -d c0t0d0
       RAID Volume 'c0t0d0' deleted

       Example 4: Updating Flash Images on the Controller

       The following command updates flash images on the controller:

       # raidctl -F lsi1030.fw 0
       Update flash image on controller 0? (y/N): y
       Flash updated successfully

EXIT STATUS

       The following exit values are returned:

       0	Successful completion.

       1	Invalid command line input.

       2	Request operation failed.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcsu			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       attributes(5)

       System Administration Guide: Basic Administration

SunOS 5.10							    17 Aug 2004 						       raidctl(1M)