MKFS.FAT(8)                                                   System Manager's Manual                                                  MKFS.FAT(8)

NAME

       mkfs.fat - create an MS-DOS filesystem under Linux

SYNOPSIS

       mkfs.fat [OPTIONS] DEVICE [BLOCK-COUNT]

DESCRIPTION

       mkfs.fat is used to create an MS-DOS filesystem under Linux on a device (usually a disk partition).  DEVICE is the special file correspond-
       ing to the device (e.g. /dev/sdXX).  BLOCK-COUNT is the number of blocks on the device.  If omitted, mkfs.fat automatically determines  the
       filesystem size.

OPTIONS

       -a  Normally,  for any filesystem except very small ones, mkfs.fat will align all the data structures to cluster size, to make sure that as
           long as the partition is properly aligned, so will all the data structures in the filesystem.  This option disables alignment; this may
           provide  a  handful  of additional clusters of storage at the expense of a significant performance degradation on RAIDs, flash media or
           large-sector hard disks.

        -A Use Atari variation of the MS-DOS filesystem.  This is default if mkfs.fat is run on an Atari, then this option turns off Atari format.
           There are some differences when using Atari format: If not directed otherwise by the user, mkfs.fat will always use 2 sectors per clus-
           ter, since GEMDOS doesn't like other values very much.  It will also obey the maximum number of  sectors  GEMDOS  can  handle.   Larger
           filesystems  are  managed by raising the logical sector size.  Under Atari format, an Atari-compatible serial number for the filesystem
           is generated, and a 12 bit FAT is used only for filesystems that have one of the usual floppy sizes (720k, 1.2M, 1.44M,  2.88M),  a  16
           bit  FAT otherwise.  This can be overridden with the -F option.  Some PC-specific boot sector fields aren't written, and a boot message
           (option -m) is ignored.

       -b SECTOR-OF-BACKUP
           Selects the location of the backup boot sector for FAT32.  Default depends on number of reserved sectors, but usually is sector 6.  The
           backup must be within the range of reserved sectors.

       -c  Check the device for bad blocks before creating the filesystem.

       -C  Create  the file given as DEVICE on the command line, and write the to-be-created filesystem to it.  This can be used to create the new
           filesystem in a file instead of on a real device, and to avoid using dd in advance to create a file of  appropriate  size.   With  this
           option,  the BLOCK-COUNT must be given, because otherwise the intended size of the filesystem wouldn't be known.  The file created is a
           sparse file, which actually only contains the meta-data areas (boot sector, FATs, and root directory).   The  data  portions  won't  be
           stored  on  the disk, but the file nevertheless will have the correct size.  The resulting file can be copied later to a floppy disk or
           other device, or mounted through a loop device.

       -D DRIVE-NUMBER
           Specify the BIOS drive number to be stored in the FAT boot sector.  This value is usually 0x80 for  hard  disks  and  0x00  for  floppy
           devices or partitions to be used for floppy emulation.

       -f NUMBER-OF-FATS
           Specify the number of file allocation tables in the filesystem.  The default is 2.

       -F FAT-SIZE
           Specifies  the  type  of  file  allocation tables used (12, 16 or 32 bit).  If nothing is specified, mkfs.fat will automatically select
           between 12, 16 and 32 bit, whatever fits better for the filesystem size.

       -h NUMBER-OF-HIDDEN-SECTORS
           Select the number of hidden sectors in the volume.  Apparently some digital cameras get indigestion if you feed them a CF card  without
           such hidden sectors, this option allows you to satisfy them.

       -i VOLUME-ID
           Sets the volume ID of the newly created filesystem; VOLUME-ID is a 32-bit hexadecimal number (for example, 2e24ec82).  The default is a
           number which depends on the filesystem creation time.

       -I  It is typical for fixed disk devices to be partitioned so, by default, you are not permitted to create a filesystem across  the  entire
           device.   mkfs.fat will complain and tell you that it refuses to work.  This is different when using MO disks.  One doesn't always need
           partitions on MO disks.  The filesystem can go directly to the whole disk.  Under other OSes this is known as the 'superfloppy' format.
           This switch will force mkfs.fat to work properly.

       -l FILENAME
           Read the bad blocks list from FILENAME.

       -m MESSAGE-FILE
           Sets the message the user receives on attempts to boot this filesystem without having properly installed an operating system.  The mes-
           sage file must not exceed 418 bytes once line feeds have been converted to carriage return-line feed combinations, and tabs  have  been
           expanded.  If the filename is a hyphen (-), the text is taken from standard input.

       -M FAT-MEDIA-TYPE
           Specify the media type to be stored in the FAT boot sector.  This value is usually 0xF8 for hard disks and is 0xF0 or a value from 0xF9
           to 0xFF for floppies or partitions to be used for floppy emulation.

       -n VOLUME-NAME
           Sets the volume name (label) of the filesystem.  The volume name can be up to 11 characters long.  The default is no label.

       -r ROOT-DIR-ENTRIES
           Select the number of entries available in the root directory.  The default is 112 or 224 for floppies and 512 for hard disks.

       -R NUMBER-OF-RESERVED-SECTORS
           Select the number of reserved sectors.  With FAT32 format at least 2 reserved sectors are needed, the default  is  32.   Otherwise  the
           default is 1 (only the boot sector).

       -s SECTORS-PER-CLUSTER
           Specify the number of disk sectors per cluster.  Must be a power of 2, i.e. 1, 2, 4, 8, ... 128.

       -S LOGICAL-SECTOR-SIZE
           Specify  the  number  of  bytes per logical sector.  Must be a power of 2 and greater than or equal to 512, i.e. 512, 1024, 2048, 4096,
           8192, 16384, or 32768.  Values larger than 4096 are not conforming to the FAT file system specification and may not work everywhere.

       -v  Verbose execution.

       --invariant
           Use constants for normally randomly generated or time based data such as volume ID and creation time.  Multiple runs of mkfs.fat on the
           same device create identical results with this option.  Its main purpose is testing mkfs.fat.

       --help
           Display option summary and exit.

BUGS

       mkfs.fat can not create boot-able filesystems.  This isn't as easy as you might think at first glance for various reasons and has been dis-
       cussed a lot already.  mkfs.fat simply will not support it ;)

SEE ALSO

       fatlabel(8)
       fsck.fat(8)

HOMEPAGE

       The home for the dosfstools project is its GitHub project page <https://github.com/dosfstools/dosfstools>.

AUTHORS

       dosfstools were written by Werner Almesberger <werner.almesberger@lrc.di.epfl.ch>,  Roman  Hodek  <Roman.Hodek@informatik.uni-erlangen.de>,
       and others.  The current maintainer is Andreas Bombe <aeb@debian.org>.

dosfstools 4.1                                                      2016-01-25                                                         MKFS.FAT(8)