05-23-2004
Just a hint. The most probarbaly the network card might have failed to detect the speed or the make of the card. Check your Network card model and make sure its been specified in the /etc/modules.conf
8 More Discussions You Might Find Interesting
1. IP Networking
Here are some really stupid questions, but I'm not really sure what I'm doing, so any help will be appreciated. I'm trying to learn linux and basic networking. I have 2 computers: one has windows and the other I just installed Red Hat 7.1. In the network configuration screen of the Red Hat... (10 Replies)
Discussion started by: satops
10 Replies
2. UNIX for Dummies Questions & Answers
I have a SunOS 5.8 box and have always downloaded & applied patches via my PC, but I want to be able to go out to sunsolve directly from the console ... however, I guess it doesn't know the IP of our domain's DNS server or something.
Where are these setting held on a Sun box??? (1 Reply)
Discussion started by: FredSmith
1 Replies
3. UNIX for Dummies Questions & Answers
OK, here's a question from a true UNIX newb: How does one make a 20 line file? I'm lost. :confused:
OK, I figured it out. :D (0 Replies)
Discussion started by: Kitchen Zinc
0 Replies
4. UNIX for Dummies Questions & Answers
Hi-
Newbie here with some basic questions:
1) I can't get alias to work. I tried alias ll='ls -al', but it doesn't work. When just typing 'alias', the new definition doesn't appear. I'm in a bash shell -- is that the problem. I tried switching to csh, but that didn't seem to help. This... (5 Replies)
Discussion started by: Aworstell
5 Replies
5. UNIX for Dummies Questions & Answers
I have multiple questions
How to list or find only Nov month's files?
How can I get state of process like running, stop, or sleep etc?
How can I check dependences of processes?
plz ans any if u can
thx regards,
Mazhar Hussain (3 Replies)
Discussion started by: mazhar99
3 Replies
6. IP Networking
I am running Ubuntu Desktop and Ubuntu Server editions on two separate VMs.
For the desktop I have set network adapters:
Adapter 1: internal network called intnet
Adapter 2: NAT
Server:
Adapter 1: internal network called intnet
Now I'm suppose to set ip addresses which I'm pretty sure... (5 Replies)
Discussion started by: shadowcat
5 Replies
7. IP Networking
Hii,
Today morning I attended an interview, they had showed me the attached image and had few questions about that.
The image shows a network with 4 nodes viz.. A B C & D and two switches(layer2) and a router(layer3). Just wanted to know can node A and node D would be on same network e.g... (4 Replies)
Discussion started by: zing_foru
4 Replies
8. Solaris
lo0: flags=1000849 <UP,LOOPBACK,RUNNING,MULTICAST,IPv4>
mtu 8232 index 1 inet 127.0.0.1 netmask ff000000
qfe0: flags=1004843 <UP,BROADCAST,RUNNING,MULTICAST,IPv4>
mtu 1500 index 2 inet 10.0.0.112 netmask ffffff80 broadcast 10.0.0.127 ether 8:0:20:b9:4c:54
qfe1: flags=1004843... (2 Replies)
Discussion started by: jtamminen
2 Replies
LEARN ABOUT CENTOS
extlinux
extlinux(1) General Commands Manual extlinux(1)
NAME
extlinux - install the SYSLINUX bootloader on a ext2/ext3 filesystem
SYNOPSIS
extlinux [options] directory
DESCRIPTION
EXTLINUX is a new syslinux derivative, which boots from a Linux ext2/ext3 filesystem. It works the same way as SYSLINUX, with a few slight
modifications. It is intended to simplify first-time installation of Linux, and for creation of rescue and other special-purpose boot
disks.
The installer is designed to be run on a mounted directory. For example, if you have an ext2 or ext3 usb key mounted on /mnt, you can run
the following command:
extlinux --install /mnt
OPTIONS
-H, --heads=#
Force the number of heads.
-i, --install
Install over the current bootsector.
-O, --clear-once
Clear the boot-once command.
-o, --once=command
Execute a command once upon boot.
-M, --menu-save=label
Set the label to select as default on the next boot
-r, --raid
Fall back to the next device on boot failure.
--reset-adv
Reset auxiliary data.
-S, --sectors=#
Force the number of sectors per track.
-U, --update
Updates a previous EXTLINUX installation.
-z, --zip
Force zipdrive geometry (-H 64 -S 32).
FILES
The extlinux configuration file needs to be named extlinux.conf and needs to be stored in the extlinux installation directory. For more
information about the contents of extlinux.conf, see syslinux(1) manpage, section files.
BUGS
I would appreciate hearing of any problems you have with SYSLINUX. I would also like to hear from you if you have successfully used SYS-
LINUX, especially if you are using it for a distribution.
If you are reporting problems, please include all possible information about your system and your BIOS; the vast majority of all problems
reported turn out to be BIOS or hardware bugs, and I need as much information as possible in order to diagnose the problems.
There is a mailing list for discussion among SYSLINUX users and for announcements of new and test versions. To join, send a message to
majordomo@linux.kernel.org with the line:
SEE ALSO
syslinux(1)
SYSLINUX for ext2/ext3 filesystem 18 December 2007 extlinux(1)