05-21-2004
Basic networking questions.
Hey, I'm new to Linux. I have a few questions about it. I run Slackware.
After the installation the Linux installation had problems with my old hardware (network card, sound card) so I removed them and Linux would start.
But now, I can't seem to use the network card in Linux because it's not installed. How do I install it? I suspect Linux had problems with the card because it's rather old. Do I need a new network card to work with Linux?
If not, please tell me how can I install it?
And how can I configure both my windows computer and linux computer to go in a network?
All I want is to set up the computers in a point to point network so I may give the Linux computer acces to internet (haven't got a clue how this works) and to be able to acces my linux box from my windows computer by Samba, putty and Webmin.
If there is any kind of online ebook or tutorial about setting up a network between a windows and linux computer please link it here for me.
But for now my most important question would be how can I install my old network card with Linux? I will find information about networking Linux and Windows eventually but it would be great if someone here would help me out.
8 More Discussions You Might Find Interesting
1. IP Networking
Here are some really stupid questions, but I'm not really sure what I'm doing, so any help will be appreciated. I'm trying to learn linux and basic networking. I have 2 computers: one has windows and the other I just installed Red Hat 7.1. In the network configuration screen of the Red Hat... (10 Replies)
Discussion started by: satops
10 Replies
2. UNIX for Dummies Questions & Answers
I have a SunOS 5.8 box and have always downloaded & applied patches via my PC, but I want to be able to go out to sunsolve directly from the console ... however, I guess it doesn't know the IP of our domain's DNS server or something.
Where are these setting held on a Sun box??? (1 Reply)
Discussion started by: FredSmith
1 Replies
3. UNIX for Dummies Questions & Answers
OK, here's a question from a true UNIX newb: How does one make a 20 line file? I'm lost. :confused:
OK, I figured it out. :D (0 Replies)
Discussion started by: Kitchen Zinc
0 Replies
4. UNIX for Dummies Questions & Answers
Hi-
Newbie here with some basic questions:
1) I can't get alias to work. I tried alias ll='ls -al', but it doesn't work. When just typing 'alias', the new definition doesn't appear. I'm in a bash shell -- is that the problem. I tried switching to csh, but that didn't seem to help. This... (5 Replies)
Discussion started by: Aworstell
5 Replies
5. UNIX for Dummies Questions & Answers
I have multiple questions
How to list or find only Nov month's files?
How can I get state of process like running, stop, or sleep etc?
How can I check dependences of processes?
plz ans any if u can
thx regards,
Mazhar Hussain (3 Replies)
Discussion started by: mazhar99
3 Replies
6. IP Networking
I am running Ubuntu Desktop and Ubuntu Server editions on two separate VMs.
For the desktop I have set network adapters:
Adapter 1: internal network called intnet
Adapter 2: NAT
Server:
Adapter 1: internal network called intnet
Now I'm suppose to set ip addresses which I'm pretty sure... (5 Replies)
Discussion started by: shadowcat
5 Replies
7. IP Networking
Hii,
Today morning I attended an interview, they had showed me the attached image and had few questions about that.
The image shows a network with 4 nodes viz.. A B C & D and two switches(layer2) and a router(layer3). Just wanted to know can node A and node D would be on same network e.g... (4 Replies)
Discussion started by: zing_foru
4 Replies
8. Solaris
lo0: flags=1000849 <UP,LOOPBACK,RUNNING,MULTICAST,IPv4>
mtu 8232 index 1 inet 127.0.0.1 netmask ff000000
qfe0: flags=1004843 <UP,BROADCAST,RUNNING,MULTICAST,IPv4>
mtu 1500 index 2 inet 10.0.0.112 netmask ffffff80 broadcast 10.0.0.127 ether 8:0:20:b9:4c:54
qfe1: flags=1004843... (2 Replies)
Discussion started by: jtamminen
2 Replies
LEARN ABOUT OPENDARWIN
network_namespaces
NETWORK_NAMESPACES(7) Linux Programmer's Manual NETWORK_NAMESPACES(7)
NAME
network_namespaces - overview of Linux network namespaces
DESCRIPTION
Network namespaces provide isolation of the system resources associated with networking: network devices, IPv4 and IPv6 protocol stacks, IP
routing tables, firewall rules, the /proc/net directory (which is a symbolic link to /proc/PID/net), the /sys/class/net directory, various
files under /proc/sys/net, port numbers (sockets), and so on.
A physical network device can live in exactly one network namespace. When a network namespace is freed (i.e., when the last process in the
namespace terminates), its physical network devices are moved back to the initial network namespace (not to the parent of the process).
A virtual network (veth(4)) device pair provides a pipe-like abstraction that can be used to create tunnels between network namespaces, and
can be used to create a bridge to a physical network device in another namespace. When a namespace is freed, the veth(4) devices that it
contains are destroyed.
Use of network namespaces requires a kernel that is configured with the CONFIG_NET_NS option.
SEE ALSO
nsenter(1), unshare(1), clone(2), veth(4), proc(5), sysfs(5), namespaces(7), user_namespaces(7), brctl(8), ip(8), ip-address(8), ip-
link(8), ip-netns(8), iptables(8), ovs-vsctl(8)
COLOPHON
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the
latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.
Linux 2018-02-02 NETWORK_NAMESPACES(7)