Sponsored Content
Operating Systems Solaris How to get to the OK prompt without Sun keyboard Post 51137 by Optimus_P on Tuesday 11th of May 2004 05:28:35 PM
Old 05-11-2004
stop-n will set all the nvram variables back to the defaults and you should then be able to get to OBP then you can check if your drive is installed then you should be able to boot off cdrom and get to the install
 

8 More Discussions You Might Find Interesting

1. Solaris

keyboard & monitor for SUn ultra enterprise 3000

Hi all, i just purchased Sun Ultra Enterprise 3000, but they did not include with keyboard/mouse . i am very new with this box. could you give me which type of keyboard i can use and video connector to my monitor since serial connectors for keyboard and video is different with my PC. ... (5 Replies)
Discussion started by: waterbear
5 Replies

2. Solaris

How to get to a OK prompt on new SUN T5140

Hi, I have a brand new SUN T5140 machine. I am trying to install Solaris 10 on the box. When I go to the machine using a KVM session I can see a blank screen , how can I get to the OK prompt to start the installation. Thanks, Suresh (10 Replies)
Discussion started by: gunnervarma
10 Replies

3. Solaris

SUN Type 7 Keyboard, Thinklogical KVM Extender and Mouse - Any ideas?

Hello all rather new to diagnosing hardware issues on SUN platforms (still new to Sol 10 also). Sorry if this is not a great question. I have searched the forums and have not found an answer to my specific issue. Ok, I have a SUN V215 hooked up to a Thinklogical KVM extender. There are 2... (3 Replies)
Discussion started by: caddyjoe77
3 Replies

4. Hardware

Sun Blade 1000 keyboard not detected.

Hello, I have a sun blade 1000 machine, it passes post, has 2 750mhz sparc 3 cpus and has 4GB of ram. I have setup a TIP connection and did everything i could to figure what the hell is going on, but I cannot it seems to me that the usb ports are not giving out any power. I've tried all... (0 Replies)
Discussion started by: binary0x01
0 Replies

5. Solaris

XSCF prompt disappeared, Sun M5000

Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out. exit rebootxscf logout #. #> #> ~# ~# exit sendbreak exit I tried to set the Mode Switch to the service... (3 Replies)
Discussion started by: aixlover
3 Replies

6. Solaris

Sun Ultra 5 Cahnge Keyboard Type

Hi, I have a Sun Ultra 5 workstation with Sun Keyboard Type 6. My problem is the workstation recognize the keyboard as Keyboard Type 4 instead of type 6. How can I change the workstation to recognize sun keyboard type 6. Any idea? # kbd -t Type 4 Sun keyboard :wall::wall::wall: (2 Replies)
Discussion started by: fairus
2 Replies

7. UNIX for Dummies Questions & Answers

Problem getting vertical bar with British keyboard layout on US (physical) keyboard

Hi, I've got a bit of a ridiculous problem and wasn't sure where to post it. I need to use the vertical bar for piping in Bash but, as per the title, am using a UK layout on a US (physical) keyboard which doesn't have a key for it in the place I'd expect. I've tried using xbindkeys and Unicode... (7 Replies)
Discussion started by: crunchgargoyle
7 Replies

8. Solaris

Sun V445 hangs before {0} ok prompt

I am having a problem when booting my Sun V445 machine with Solaris 10 installed on it. Machine hangs at boot at following step : 0>Copyright 2007 Sun Microsystems, Inc. All rights reserved 0>OBP->POST Call with %o0=00000800.01014000. 0>Diag level set to MAX. 0>Verbosity level set to... (21 Replies)
Discussion started by: usmanijaz101
21 Replies
nvram(8)						      System Manager's Manual							  nvram(8)

NAME
nvram - manipulate firmware NVRAM variables SYNOPSIS
nvram [ -p ] [ -f filename ] [ -d name ] [ -c ] [ name [= value ]] ... DESCRIPTION
The nvram command allows manipulation of firmware NVRAM variables. It can be used to get or set a variable. It can also be used to print all of the variables or set a list of variables from a file. Changes to NVRAM variables are only saved by clean restart or shutdown. In principle, name can be any string. In practice, not all strings will be accepted. New World machines can create new variables as desired. Some variables require administrator privilege to get or set. The given value must match the data type required for name. Binary data can be set using the %xx notation, where xx is the hex value of the byte. The type for new variables is always binary data. OPTIONS
-d name Deletes the named firmware variable. -f filename Set firmware variables from a text file. The file must be a list of "name value" statements. The first space on each line is taken to be the separator between "name" and "value". If the last character of a line is , the value extends to the next line. -x Use XML format for reading and writing variables. This option must be used before the -p or -f options, since arguments are pro- cessed in order. -c Delete all of the firmware variables. -p Print all of the firmware variables. EXAMPLES
example% nvram boot-args="-s rd=*hd:10" Set the boot-args variable to "-s rd=*hd:10". This would specify single user mode with the root device in hard drive partition 10. example% nvram my-variable="String One%00String Two%00%00" Create a new variable, my-variable, containing a list of two C-strings that is terminated by a NUL. example% nvram -d my-variable Deletes the variable named my-variable. October 28, 2003 nvram(8)
All times are GMT -4. The time now is 06:52 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy