05-07-2004
Also if you do not get anything to come up for you on the serial port, you will have to reset the defaults of the console to be redirected to ttya.
Where did you get this 280R?
Jonathan
10 More Discussions You Might Find Interesting
1. Solaris
hi!!!!!!
how to upgrade sunfire 280R server from solaris8 to solaris9?
pls help me.
Thanks & Regards
-Vishal (1 Reply)
Discussion started by: Vishal Shroff
1 Replies
2. Solaris
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies
3. Solaris
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Discussion started by: hcclnoodles
4 Replies
4. Solaris
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Discussion started by: mgb
2 Replies
5. Solaris
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
Discussion started by: lamoul
3 Replies
6. Solaris
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Discussion started by: lamoul
1 Replies
7. Solaris
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Discussion started by: lamoul
2 Replies
8. Solaris
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
Discussion started by: lamoul
7 Replies
9. Hardware
Hi,
I'm a newbie in the Unix world... :confused:
I own a Sun Sunfire 280R computer with one 750Mhz CPU. I ordered two CPU of 900Mhz to replace it; however in the Service manual from Sun I read that to use 900Mhz CPU i will need to have a OBP of at least version 4.5.16. When I type .version in... (2 Replies)
Discussion started by: Monkey114
2 Replies
10. Hardware
I got the system couple of days back from one of my friend. Last night I turned it on and I noticed that maintenance LED is on. At the same time I added an LCD monitor via VGA and nothing was showing on the screen. Though the system does not have any HDD So not sure if system will even show a BIOS... (3 Replies)
Discussion started by: pgirish007
3 Replies
LEARN ABOUT PLAN9
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)