05-07-2004
Also if you do not get anything to come up for you on the serial port, you will have to reset the defaults of the console to be redirected to ttya.
Where did you get this 280R?
Jonathan
10 More Discussions You Might Find Interesting
1. Solaris
hi!!!!!!
how to upgrade sunfire 280R server from solaris8 to solaris9?
pls help me.
Thanks & Regards
-Vishal (1 Reply)
Discussion started by: Vishal Shroff
1 Replies
2. Solaris
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies
3. Solaris
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Discussion started by: hcclnoodles
4 Replies
4. Solaris
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Discussion started by: mgb
2 Replies
5. Solaris
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
Discussion started by: lamoul
3 Replies
6. Solaris
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Discussion started by: lamoul
1 Replies
7. Solaris
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Discussion started by: lamoul
2 Replies
8. Solaris
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
Discussion started by: lamoul
7 Replies
9. Hardware
Hi,
I'm a newbie in the Unix world... :confused:
I own a Sun Sunfire 280R computer with one 750Mhz CPU. I ordered two CPU of 900Mhz to replace it; however in the Service manual from Sun I read that to use 900Mhz CPU i will need to have a OBP of at least version 4.5.16. When I type .version in... (2 Replies)
Discussion started by: Monkey114
2 Replies
10. Hardware
I got the system couple of days back from one of my friend. Last night I turned it on and I noticed that maintenance LED is on. At the same time I added an LCD monitor via VGA and nothing was showing on the screen. Though the system does not have any HDD So not sure if system will even show a BIOS... (3 Replies)
Discussion started by: pgirish007
3 Replies
scc(7) Miscellaneous Information Manual scc(7)
NAME
scc - Serial keyboard/mouse/communications interface
SYNOPSIS
controller scc0 at tc0 slot 3 vector sccintr
DESCRIPTION
Two base board Zilog scc dual UARTS provide DEC 3000 series personal systems with keyboard, mouse, and serial communications interfaces.
The serial communications interfaces can operate at baud rates from B50 to B57600 (see tty(7)).
The driver for the scc interface supports hardware flow control using the Request to Send (RTS) and Clear to Send (CTS) signals. When
hardware flow control is enabled, the flow of input data is controlled by the RTS signal and the flow of output data is controlled by the
CTS signal. If the CTS signal is off, the driver will suspend output to that line until the CTS lead is reasserted. Likewise, the driver
will turn off the RTS lead to tell the device connected to the line to stop sending data as a result of congestion on the host side. When
the condition clears, the driver will turn on the RTS lead to tell the device to resume sending data.
In alternate console configurations (that is, no graphics head), communications port 2 (/dev/tty01) becomes the system console. The serial
system console port always operates at 9600 BPS, 8-bits, no parity. No modem or hardware flow control is supported.
RESTRICTIONS
Data communications equipment attached to the console serial port in alternate console configurations must be set to 9600 BPS, 8-bits, no
parity. The scc driver enforces this restriction.
Only communications port 1 (/dev/tty00) includes full modem control.
FILES
console terminal local terminal local terminal
RELATED INFORMATION
console(7), devio(7), modem(7), tty(7), MAKEDEV(8) delim off
scc(7)