|
|
Sponsored Content
Operating Systems
Solaris
pls help urgently....for SUNfire 280R
Post 50997 by weftnet.com on Friday 7th of May 2004 04:28:25 PM
05-07-2004
|
|
10 More Discussions You Might Find Interesting
1. Solaris
hi!!!!!!
how to upgrade sunfire 280R server from solaris8 to solaris9?
pls help me.
Thanks & Regards
-Vishal (1 Reply)
Discussion started by: Vishal Shroff
1 Replies
2. Solaris
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies
3. Solaris
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Discussion started by: hcclnoodles
4 Replies
4. Solaris
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Discussion started by: mgb
2 Replies
5. Solaris
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
Discussion started by: lamoul
3 Replies
6. Solaris
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Discussion started by: lamoul
1 Replies
7. Solaris
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Discussion started by: lamoul
2 Replies
8. Solaris
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
Discussion started by: lamoul
7 Replies
9. Hardware
Hi,
I'm a newbie in the Unix world... :confused:
I own a Sun Sunfire 280R computer with one 750Mhz CPU. I ordered two CPU of 900Mhz to replace it; however in the Service manual from Sun I read that to use 900Mhz CPU i will need to have a OBP of at least version 4.5.16. When I type .version in... (2 Replies)
Discussion started by: Monkey114
2 Replies
10. Hardware
I got the system couple of days back from one of my friend. Last night I turned it on and I noticed that maintenance LED is on. At the same time I added an LCD monitor via VGA and nothing was showing on the screen. Though the system does not have any HDD So not sure if system will even show a BIOS... (3 Replies)
Discussion started by: pgirish007
3 Replies
LEARN ABOUT ULTRIX
mdc
mdc(4) Kernel Interfaces Manual mdc(4) Name mdc - DS5100 serial line driver Syntax device mdc0 at ibus? vector mdcintr device mdc1 at ibus? vector mdcintr device mdc2 at ibus? vector mdcintr Description A DS5100 base system (mdc0) provides four asynchronous ports. An optional asynchronous card (mdc1 and mdc2 ) can be added to supply eight additional ports. The mdc ports are used as follows: Port Usage Connector 0 Console port 6-pin MMJ on CPU board 1 Local terminal 6-pin MMJ on CPU board 2 Full modem control port 25-pin D-Sub on CPU board 3 Local terminal 6-pin MMJ on CPU board An optional asynchronous board provides an additional eight lines: 4 Local terminal 6-pin MMJ 5 Local terminal 6-pin MMJ 6 Full modem control port 25-pin D-Sub 7 Local terminal 6-pin MMJ 8 Local terminal 6-pin MMJ 9 Local terminal 6-pin MMJ 10 Local terminal 6-pin MMJ 11 Local terminal 6-pin MMJ The console baud rate is set to 9600 baud by default. You can change this by setting the baud environment variable from console prompt. Each communication port from the serial line controller behaves as described in the reference page and can be set to run at any of 16 speeds. For the encoding, see You can establish the state of port 2 (port 6) by specifying either modem or nomodem as part of the file entry. Restrictions The speed default is to 9600 baud on the console port. The console device must be set for 8-bit character length with one stop bit and no parity. The driver enforces these restrictions; that is, changing speeds with the command may not always work on console ports. Files Console terminal Full modem control or local terminal See Also console(4), devio(4), tty(4), ttys(5), MAKEDEV(8) RISC mdc(4)